Manuals / Hobart / Kitchen Appliance / Freezer

Hobart ML-124068, HQC90, HQCF45, ML-124066 manual Alarms, Access the Sys Par 2 menu as shown on page

Models: ML-124067 ML-124066 HQCF45 HQC90 ML-124068

1 32

Page 25

•Access the Sys Par 2 menu as shown on page 21.

SYS PAR 1	09:07:31
CLOCK TEMPS IN °F
PROBES	LOGGING
SETUP MENU	MORE	SYS PAR 2		09:08:41
		REMOTE ALARM MODE
		ALARMS		BUZZER
		BACK	FAC PRESETS

ALARMS

ALARM TIME SETTINGS: ↓DOOR OPEN=120 SECS↑ ↓CLEAN COIL=30 DAYS↑

ENTER

•From Sys Par 2, select ALARMS.

•Use the ↓ or ↑ keys to adjust the DOOR OPEN setting. Range = 0, 30, 60, 90, 120, 150, 180, 210, 240 seconds. Refer to page 24.

•Use the ↓ or ↑ keys to adjust the CLEAN COIL setting. Range = 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90 days. The CLEAN COIL setting determines how many days the compressor will run before a display appears to remind you to clean the condenser coil.

•Select ENTER to accept the displayed values and return to SYS PAR 2.

– 25 –

Page 25

Image 25

Hobart ML-124068, HQC90, HQCF45, ML-124066 Alarms, Access the Sys Par 2 menu as shown on page, From Sys Par 2, select ALARMS

Contents

HQCF45 QUICKCHILLER-FREEZER HQC45 & HQC90 QUICKCHILLERSMODEL HQC45 ML-124066 HQCF45 ML-124067 HQC90 ML-124068TABLE OF CONTENTS Page HQC45 & HQC90 QuickChillers Installation, Operation, Use and Care ofHQCF45 QuickChiller-Freezer GENERALUNCRATING INSTALLATIONLEGS OR CASTERS Door Switch FEATURESFan Door Switch LOCATIONINSTALLATION CHECKOUT INSTALLATION OF REMOTE ALARM OptionalELECTRICAL CONNECTIONS OPERATION OVER TEMPERATURECONTROLS Fig START-UPPRINTER SUPPLIES WHEN POWER IS RESTORED AFTER A POWER INTERRUPTIONLOADING ROLL STOCK ONTO THE PRINTERS Fig Plain Thermal PaperMAIN MENU the display goes to If all probes are ‘done,’HOLDING number to stop cycleMAIN MENU BY TIME - Timer counts down until cycle is doneFrom the Main Menu, select BY TIME Hr Min Sec Remove all chilled product From the Main Menu, select BY PROD MAIN MENUFollow the cycle run information on pages beginning atbeginning at PRODUCT LIST From the Main Menu, select MORE and HOLD PROD chilling but only if operating in Holding mode DEFROSTPRODUCTS SETUPSETUP USERSSYS PAR CLOCK TEMPS IN F PROBESLOGGING REMOTE ALARM Access the Sys Par 2 menu as shown on page ALARMSFrom Sys Par 2, select ALARMS CHILL MODEMODE Access the Sys Par 2 menu as shown on pageSet the AIR Temp using the ↓ or ↑ keys Set the TARGET Temp using the ↓ or ↑ keysSet the HOLD Temp using the ↓ or ↑ keys Set the HIGH ALARM Temp using the ↓ or ↑ keysBUZZER FAC PRESETSGLOSSARY During communication with the SmartChill program COMMUNICATION WITH SmartChillon a PC, the screen at left displays CLEANING MAINTENANCEERROR MESSAGES MAINTENANCE PROGRAM