Fire Alarm System cont’d, Individual Keys | Honeywell VISTA-21IP

Fire Alarm System (cont’d)

THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

Manually

Initiating

a Fire Alarm

Using the Panic Key(s) Assigned for

FIRE Emergency

1.Should you become aware of a fire emergency before your smoke or heat detectors sense the problem, go to your nearest keypad and manually initiate an alarm by pressing the panic key assigned for FIRE emergency for 2 seconds (see below). If a key pair has been assigned for fire, press both keys at the same time. See the Using the Panic Keys section below for further details.

2.Evacuate all occupants from the premises.

3.If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately.

4.If no flames or smoke are apparent, investigate the cause of the alarm. The zone number(s) of the zone(s) in an alarm condition will be displayed at the keypad.

A key or key pair may have been assigned for manually initiating a FIRE alarm. See the Panic Keys section for key assignments.

For convenience, indicate the key or key pair assigned for fire below.

Individual Keys

A B C

Press the individual key assigned for fire for 2 seconds.

OR Key Pairs


1 OFF		and			∗ READY			(zone 95)

∗ READY			and			#		(zone 99)

3 STAY			and		#			(zone 96)

Press both keys of the key pair assigned for fire at the same time.

Carbon

Monoxide

Alarms

DISPLAYS FOLLOWING MANUAL INITIATION OF A FIRE ALARM

		95	AC
F I R E 9 5			AC
F I R E 9 5
		ALARM
		FIRE



ALPHA DISPLAY KEYPAD		FIXED-WORD KEYPAD

If installed, carbon monoxide detectors provide continuous protection. If a high level of carbon monoxide is detected, an interrupted pulsed alarm sound occurs at the keypads and the detector(s). Immediately move to a spot where fresh air is available, preferably outdoors. From a safe area, call your security service provider for further instructions. To silence the keypad sounding, press the OFF key. To silence the detector, see its instructions.

– 47 –

Image 47

Honeywell VISTA-21IPSIA manual Fire Alarm System cont’d, Individual Keys, Or Key Pairs

Contents

Ademco Vista Series About This Manual Table of Contents Table of Contents System Basics System OverviewIntroduction System Overview cont’d Scheduling Using the Voice Message Center if Voice Keypad is installedPaging Feature Function Keys General Information About The Keypads Armed Ready Message MIC About The Keypads cont’d FIXED-WORD Display Keypad Armed Ready Message MIC Functions of the Keypads Functions of the Keypads cont’d MIC Exit Delay Entry/Exit DelaysEntry Delay Exit Error Conditions Entry/Exit Delays cont’dExit Alarms Checking For Open Zones Using the ∗ Key to Display and Announce System StatusTo turn the Voice Status feature on/off # Arming the System Instant Mode Arms Perimeter Only, Entry Delay OffAway Mode Arms Entire System, Entry Delay On Maximum Mode Arms Entire System, Entry Delay Off Quick Arming Arming CommandsMode Press these keys… Keypad Confirms By… Arming the System cont’d Key First Press Second Press Third Press Single Button ArmingSingle Button Step Arming To arm in the Stay mode KeyswitchUsing the Keyswitch To arm in the Away mode Using the OFF key Disarming and Silencing Alarms Bypassing Protection Zones Using the Bypass Key Quick Bypass Bypassing Protection Zones cont’d Using the Voice Chime Chime ModeUsing the Chime Mode Viewing the Current Date and Time Setting the Date and TimeDate and Time To activate a Panic Function Using Panic KeysThis Function Sends This Signal With This Sounding… Panic Keys About Macro Keys Macro Key Programming & Usage Example of Macro Programming Using a Programmed Macro KeyMacro Key Programming & Usage cont’d To Deactivate Devices Using Device CommandsAbout Device Commands To Activate Devices About Automatic Paging Paging Feature Latch Key Paging Paging Feature cont’dAbout Manual Paging Authority Level Definitions Security Codes & Authority LevelsAbout Security Codes Security Codes & Authority Levels cont’d How to Assign Security Codes and Attributes Goto Command and Multi-Partition Arming Accessing Other PartitionsAbout Accessing Partitions Multi-Partition Arming Accessing Other Partitions cont’dUsing the GoTo Command Common Zone Operation About Scheduling Scheduling Scheduling cont’d Understanding the Type of Event Displayed Event Logging ProceduresAbout Event Logging Viewing the Event Log STAY/INSTANT Event Logging Procedures cont’d About Testing the System Testing the System Trouble Conditions If there are wireless sensors* in your system, the Check Or Check Alarm 1xx Fault 1xx CheckTrouble Conditions cont’d Rcvr Jam Long Rng Trbl Or no ACBusy-Standby Maintaining Your System This Section Applies only to Residential Systems Fire Alarm System Or Key Pairs Fire Alarm System cont’dIndividual Keys Kitchen Dining Emergency Evacuation Quick Guide to Basic System Functions Function Procedure Comments Fixed-Word Display Keypads Summary of Audible/Visual Notifications Alpha Display Keypads Summary of A/V Notifications cont’d Industry Canada Regulatory Statements and WarningsFCC Part Industrie Canada Regulatory Statements cont’dRinger Equivalence Number Notice System Features Log User Setup System Features Log cont’d Paging Setup User Setup cont’d List of Output Devices OWNER’S Insurance Premium Credit Request Cont Page Page Limitations of this System ÊK14490V1Š