Manuals / Honeywell / Household Appliance / Home Security System

Honeywell 128BPTSIA, VISTA250BPT, VISTA128BPT manual Trouble Conditions, Typical Trouble Displays

Models: VISTA250BPT 128BPTSIA VISTA128BPT

1 80

Download 80 pages 21.98 Kb

Page 62

Trouble Conditions

Trouble Conditions

Typical Trouble Displays

The word CHECK or TRBL on the Keypad's display, accompanied by a rapid "beeping" at the Keypad, indicates that there is a trouble condition in the system.

To silence the beeping sound for trouble conditions, press any key.

•A display of “CHECK” or “TRBL” accompanied by a display of "CALL SERVICE" indicates that a problem exists with the system that

eliminates some of the protection. CALL FOR SERVICE IMMEDIATELY.

•A display of “CHECK” or “TRBL" accompanied by a display of one or more zone descriptors indicates that a problem exists with those zone(s)*. First, determine if the zone(s) displayed are intact and make them so if they are not. If the problem has been corrected, the display of the zone descriptor(s) and “CHECK” or “TRBL” should disappear. If not, key an OFF sequence (Code plus OFF) to clear the display. If the display persists, CALL FOR SERVICE IMMEDIATELY.

•A display of “CHECK” or “TRBL” accompanied by a numeric display of “6XX,” where XX = 01-32, indicates a trouble on a supervised relay (corresponding relay number 01-32).

•A display of “CHECK” or “TRBL” accompanied by a numeric display of “8XX,” where XX = 00-30, indicates a trouble on a peripheral device (connected to the panel’s keypad terminals) of a corresponding device address (00-30).

•A display of “CHECK” or “TRBL” accompanied by a numeric display of “9XX,” where XX = 00-99, indicates a system trouble exists (RF Receivers, Bell output, etc.). These zones are as follows:

970: Bell Supervision

988:2nd RF Receiver – not receiving signals

990:1st RF Receiver – not receiving signals

997:Polling Loop Short

•A display of "COMM. FAILURE" at the Keypad indicates that a failure has occurred in the telephone communication portion of your system.

CALL FOR SERVICE IMMEDIATELY.

– 62 –

Image 62

Honeywell 128BPTSIA, VISTA250BPT, VISTA128BPT manual Trouble Conditions, Typical Trouble Displays

Contents

With Scheduling User Guide VISTA-128BPT VISTA-250BPT VISTA-128BPTSIACommercial Burglary Partitioned Security System Page TABLE OF CONTENTS Page System Overview GeneralA Partitioned System AlarmsSystem Overview cont’d ZonesFeatures For Each Arming Mode Memory of AlarmBurglary Protection System Overview cont’dTo Access another Partition GOTO Command Using SchedulesDevice Timers Speed Key MacrosSystem Overview cont’d Self-HelpFeaturePhone Access & Voice Response Capability General About The KeypadsThe Alpha Keypad SPEAKER Functions of the KeypadB CD LEDSRemoves Functions of the Keypad cont’d6 BYPASS individualFunctions of the Keypad cont’d Entry/Exit Delays General InformationDuress Code Installer Code LockoutSecurity Codes and Authority Levels Quick ArmingSecurity Codes and Authority Levels cont’d Authority LevelsSecurity Codes and Authority Levels cont’d General Rules on Authority Levels and ChangesTo Exit User Edit Mode CODE To Add a UserSecurity Codes and Authority Levels cont’d GLOBAL ARM ? 0 = NO , 1 = YES MULTI-ACCESS? 0 = NO , 1 = YESSecurity Codes and Authority Levels cont’d PART.2 - SHOP? 0 = NO , 1 = YESTo Change a Users Code Security Codes and Authority Levels cont’dTo Delete a User Security Codes and Authority Levels cont’dGlobal Arming Accessing Other PartitionsTo Access another Partition ARM P 1 2 3 4 5 6 7 8 HITMaster Keypad Operation Accessing Other Partitions cont’dGlobal Arming Notes FAULT 002 LOADING DOCK WINDOW Accessing Other Partitions cont’dWHSE DISARMED HIT ∗ FOR FAULTS Common Lobby Operation Accessing Other Partitions cont’dCodes with “Non-Global”Arming How User Codes Affect the Common LobbyCodes with “Global” Arming Other Methods of Arming/DisarmingTypical fault display Using theTo show faulted zones Checking For Open ZonesUsing the Displaying All Zone Descriptorsdescriptors can be displayed READY KeyUsing the Bypassing Protection Zones6 BYPASS Key Quick Bypass To use the Quick Bypass featureBypassing Protection Zones cont’d Viewing Bypassed ZonesBypassing Protection Zones cont’d To use the Group Bypass featureGroup Bypass Zones Remaining Bypassed After Disarming Bypassing Protection Zones cont’dSTAY key With Entry Delay ONArming Perimeter Only Using theArming Perimeter Only With Entry Delay ON cont’dAuto-STAYArming Using the With Entry Delay OFFINSTANT Key Arming Perimeter OnlyWith Entry Delay ON Using the 2 AWAY KeyArming All Protection Using the MAXIMUM KeyWith Entry Delay OFF Arming All ProtectionTo Quick Exit the premises Using the # + 9 KeysQuick Exit Memory of Alarm Disarming and Silencing AlarmsUsing the 1 OFF Key Disarming Using the KeyswitchArming To arm in the STAY mode, turn theUsing the Chime Mode9 Key Viewing Alarm Company Messages General InformationActive Panic Functions Using Panic KeysPanic Keys General Information Speed Key MacrosDefining Speed Key Macros cont’d ExecutingExecuting Access Door ControlGeneral Information Using #70 Relay Menu Mode General InformationTemporary Open/Close Schedules Using SchedulesDelaying the Closing Time To program temporary schedules Using Schedules cont’dProgramming Temporary Schedules Using Schedules cont’d DAYS ? MTWTFSS HITGeneral Information Programming Device TimersTo enter the device timer menu mode Programming Device Timers cont’d Randomize Output Device Times Programming Device Timers cont’dAction Specifier Using #77 Instant Activation ModeAction Code Action CodeAction Specifier Using #77 Instant Activation Mode cont’dAction Code Action CodeAdditional Commands To enter the Instant Activation ModeUsing #77 Instant Activation Mode cont’d Action Code3.Select the partition Event Log Procedures1.Enter CODE + # + 6 + 2.Select the display mode Typical Event Log Display5.To EXIT the Event Log Press ∗ at any time Event Log Procedures continuedALARM EVENT LOG TypicalSetting the Time and Date TEST Key Testing the System To Be Conducted WeeklyTesting Your System Using theSilencing a Fire Alarm Fire Alarm SystemIn Case Of Fire Alarm Trouble Conditions Typical Trouble DisplaysSERVICING INFORMATION Power FailureTrouble Conditions cont’d Recommendations for Proper Protection Recommendations for Smoke and Heat DetectorsIn addition, we recommend the following Recommendations for Proper Protection cont’dRecommendations for Proper Intrusion Protection Emergency Evacuation Taking Care of Your System Replacing Batteries in Wireless SensorsMaintaining Your System Routine Care Silencing Low Battery Warning Tones at the KeypadMaintaining Your System cont’d FUNCTION Quick Guide to System FunctionsPROCEDURE COMMENTSFUNCTION Quick Guide to System Functions cont’dPROCEDURE COMMENTSc. DISARM SYSTEM OR ALARM WILL OCCUR is Summary of Audible NotificationAlpha Display Keypads a. DISARM SYSTEM OR ALARM WILL OCCUR isFCC CLASS B STATEMENT IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMSFEDERAL COMMUNICATIONS COMMISSION STATEMENTS INDUSTRY CANADA CLASS B STATEMENTPage CANADIAN DEPARTMENT OF COMMUNICATIONS DOC STATEMENTTHE LIMITATIONS OF THIS ALARM SYSTEM Index Page TWO YEAR LIMITED WARRANTY Page P.O. Box 9040, Melville, NY Ê800-06905EŠ2 Corporate Center Drive, Suite