Manuals / Hoshizaki / Kitchen Appliance / Ice Maker

Hoshizaki KMD-410MAH I. Speciﬁcations A. Electrical and Refrigerant Data, Single Phase

Models: KMD-410MWH KMD-410MAH

1 30

Download 30 pages 52.81 Kb

Page 6

I. Speciﬁcations

I. Speciﬁcations

A. Electrical and Refrigerant Data

The nameplate provides electrical and refrigerant data. The nameplate is located on the right side panel. For certiﬁcation marks, see the nameplate.

We reserve the right to make changes in speciﬁcations and design without prior notice.

Single Phase

	Model Number	KMD-410MAH	KMD-410MWH
	AC Supply Voltage	115/60/1	115/60/1
	Compressor	115-120V 5.1RLA 50.0LRA	115V-120V 5.1RLA 50.0LRA
	Pump	120V 0.42FLA 23W	120V 0.42FLA 23W
	Fan	120V 0.50FLA 60W	--- --- ---
	Other	115-120V 0.15A	115-120V 0.15A
	Maximum Fuse Size	20 AMPS	20 AMPS
	Max. HACR Breaker	20 AMPS	20 AMPS
	(USA Only)	20 AMPS	20 AMPS
	(USA Only)
	Max. Circuit Breaker	20 AMPS	20 AMPS
	(Canada Only)	20 AMPS	20 AMPS
	(Canada Only)
	Minimum Circuit Ampacity	20 AMPS	20 AMPS
	Design Pressure	HI-467PSI	HI-467PSI
	Design Pressure	LO-206PSI	LO-206PSI
		LO-206PSI	LO-206PSI
	Refrigerant	R404A 18.3 oz.	R404A 14.1 oz.

5

Image 6

Hoshizaki KMD-410MAH I. Speciﬁcations A. Electrical and Refrigerant Data, Single Phase, Model Number, KMD-410MWH

Contents

Issued Modular Crescent Cuber Models KMD-410MAH KMD-410MWHAttn Hoshizaki Technical Support Department Complete and detailed explanation of the problemHOSHIZAKI AMERICA, INC 618 Highway 74 South Peachtree City, GA Phone 1-800-233-1940 Technical Support 770 487-2331 Fax 770CONTENTS Indicates a hazardous situation which could result in death or Important Safety InformationIndicates important information about the installation, use and serious injuryWARNING, continued Model Number I. Speciﬁcations A. Electrical and Refrigerant DataSingle Phase KMD-410MAHB. Dimensions/Connections 1. KMD-410MAH2. KMD-410MWH Unit mm inchesII. Installation and Operating Instructions A. Checks Before InstallationB. How to Remove Panels - See Fig C. Location Ice maker D. SetupFig. 2a MountingFig. 2b E. Bin Control Installation 9 Connect the bin control connector to the side of the control box 12 Secure the pump motor bracket with the two thumbscrews F. Electrical Connection $53*$-$0//&$5*0G. Water Supply and Drain Connections - See Fig. 9, 10 or 1. Icemaker a Connection to an Open Drain System b Connection to a Closed Loop System H. Final Checklist I. Startup III. Cleaning and Maintenance Instructions A. Cleaning1. Cleaning Procedure g. Replace the ﬂoat switch in its correct position 3 Turn off the power supply6 Turn off the power supply b. Disconnect the discharge hose9 Pour the cleaning solution into the water tank 15 Move the service switch to the DRAIN position 12 Turn on the power supply to start the washing process13 Turn off the power supply after 30 minutes 17 Turn off the power supply and remove the front panel2. Sanitizing Procedure - Following Cleaning Procedure 2. Storage Bin and Scoop B. Maintenance1. Stainless Steel Exterior 3. Air Filters air-cooled model onlyC. Preparing the Icemaker for Periods of Non-Use 1. Remove the water from the icemaker water supply line2. Drain the water tank IV. Disposal HOSHIZAKI AMERICA, INC