Manuals / Brands / Computer Equipment / Power Supply / HP / Computer Equipment / Power Supply

HP 66332A SAV, TST, Example, CAUTION:, Parameters, Command Syntax, Related Commands, Query Syntax TST, Table 4-8.*RST Settings, Returned Parameters <NR1

1 103

Download 103 pages, 546 Kb

4 - Language Dictionary

Table 4-8. *RST Settings

CAL:STAT	OFF		[SOUR:]CURR	10% of MAX*
DIG:DATA		0	[SOUR:]CURR:TRIG	10% of MAX*
DISP:STAT		ON	[SOUR:]CURR:PROT:STAT	OFF
DISP:MODE		NORM	[SOUR:]LIST:COUN	0
DISP:TEXT		‘ ‘	[SOUR:]VOLT	0
INIT:CONT		OFF	[SOUR:]VOLT:TRIG	0
OUTP		OFF	[SOUR:]VOLT:PROT	MAX*
OUTP:DFI		OFF	TRIG:ACQ:COUN:CURR	1
OUTP:DFI:SOUR		OFF	TRIG:ACQ:COUN:VOLT	1
OUTP:PROT:DEL		.08 Norm; .008 Fast	TRIG:ACQ:HYST:CURR	0
OUTP:REL		OFF	TRIG:ACQ:HYST:VOLT	0
OUTP:REL:POL		NORM	TRIG:ACQ:LEV:CURR	MAX*
SENS:CURR:RANG		MAX	TRIG:ACQ:LEV:VOLT	MAX*
SENS:CURR:DET		ACDC	TRIG:ACQ:SLOP:CURR	POS
SENS:FUNC		VOLT	TRIG:ACQ:SLOP:VOLT	POS
SENS:SWE:OFFS:POIN		0	TRIG:ACQ:SOUR	INTERNAL
SENS:SWE:POIN		2048	TRIG:TRAN:SOUR	BUS
SENS:SWE:TINT		15.6 μs

* Maximum values are model-dependent. Refer to Table 4-3.

*SAV

This command stores the present state of the dc source to the specified location in non-volatile memory. Up to 4 states can be stored. If a particular state is desired at power-on, it should be stored in location 0. It will then be automatically recalled at power turn-on if OUTPut:PON:STATe is set to RCL0. *RCL retrieves instrument states.

Command Syntax	*SAV <NRf>
Parameters	0 1 2 3
Example	*SAV	3
Related Commands	*RCL	*RST

CAUTION: *SAV causes a write cycle to nonvolatile memory. Nonvolatile memory has a finite maximum number of write cycles. Programs that repeatedly cause write cycles to nonvolatile memory can eventually exceed the maximum number of write cycles and cause the memory to fail.

*TST?

This query causes the to do a self-test and report any errors. 0 indicates that the dc source passed self- test. 1 indicates that one or more tests failed. Selftest errors are written to the error queue (see Appendix C).

Query Syntax TST?

Returned Parameters <NR1>

72

Contents

Programming Guide Safety Guidelines Printing History 1 - GENERAL INFORMATION 2 - INTRODUCTION TO PROGRAMMING 3 - PROGRAMMING THE DC SOURCE 4 - LANGUAGE DICTIONARY Output Commands Status Commands A - SCPI CONFORMANCE INFORMATION B - COMPATIBILITY LANGUAGE C - ERROR MESSAGES D - EXAMPLE PROGRAMS INDEX General Information GPIB References SCPI References Introduction to Programming Supported Applications System Requirements Downloading and Installing the Driver Accessing Online Help GPIB Address RS-232Data Format RS-232Flow Control RS-232Programming Example RS-232Troubleshooting Conventions Used in This Guide Multiple Commands in a Message Moving Among Subsystems Including Common Commands Using Queries The Message Unit Headers Query Indicator Message Unit Separator Root Specifier Numerical Data Formats Suffixes and Multipliers Response Data Types SCPI Command Completion Using Device Clear Page Programming the DC Source Power-onInitialization Enabling the Output Output Voltage Output Current Output Trigger System Model Setting the Voltage or Current Trigger Levels Initiating the Output Trigger System Generating Triggers Voltage and Current Measurements RMS Measurements (Agilent 66312A, 66332A Only) Minimum and Maximum Measurements (Agilent 66312A, 66332A Only) Current Ranges Returning Measurement Data From the Data Buffer (Agilent 66312A, 66332A Only) Measurement Trigger System Model Initiating the Measurement Trigger System (Agilent 66312A, 66332A Only) Selecting the Measurement Trigger Source (Agilent 66312A, 66332A Only) Generating Measurement Triggers (Agilent 66312A, 66332A Only) Figure 3-3.Trigger Commands Used to Measure Output Pulses Current Detector Pulse Measurement Queries Varying the Voltage or Current Sampling Rate Multiple Measurements (Agilent 66312A, 66332A Only) Pre-eventand Post-eventTriggering (Agilent 66312A, 66332A Only) Pulse Measurement Example (Agilent 66312A, 66332A only) Page Power-OnConditions Operation Status Group Questionable Status Group Standard Event Status Group Status Byte Register Determining the Cause of a Service Interrupt Servicing Operation Status and Questionable Status Events Monitoring Both Phases of a Status Transition Remote Inhibit (RI) Discrete Fault Indicator (DFI) Using the Inhibit/Fault Port as a Digital I/O DFI Programming Example Page Language Dictionary Subsystem Commands Table 4-1.Subsystem Commands Syntax Table 4-1.Subsystem Commands Syntax (continued) Page Common Commands Programming Parameters CALibrate:CURRent CALibrate:CURRent:NEGative CALibrate:CURRent:MEASure:LOWRange CALibrate:CURRent:MEASure:AC CALibrate:DATA CALibrate:LEVel CALibrate:PASSword CALibrate:SAVE CALibrate:STATe CALibrate:VOLTage CALibrate:VOLTage:PROTection MEASure:ARRay:CURRent FETCh:ARRay:CURRent MEASure:ARRay:VOLTage FETCh:ARRay:VOLTage MEASure:CURRent FETCh:CURRent MEASure:CURRent:ACDC FETCh:CURRent:ACDC MEASure:CURRent:HIGH MEASure:CURRent:LOW FETCh:CURRent:LOW MEASure:CURRent:MAXimum FETCh:CURRent: MAXimum MEASure:CURRent:MINimum MEASure:VOLTage FETCh:VOLTage MEASure:VOLTage:ACDC FETCh:VOLTage:ACDC MEASure:VOLTage:HIGH MEASure:VOLTage:LOW FETCh:VOLTage:LOW MEASure:VOLTage:MAXimum FETCh:VOLTage:MAXimum MEASure:VOLTage:MINimum SENSe:CURRent:RANGe SENSe:CURRent:DETector SENSe:FUNCtion SENSe:SWEep:OFFSet:POINts SENSe:SWEep:POINts SENSe:SWEep:TINTerval SENSe:WINDow OUTPut OUTPut:DFI OUTPut:DFI:SOURce OUTPut:PON:STATe OUTPut:PROTection:CLEar OUTPut:PROTection:DELay OUTPut:RELay OUTPut:RELay:POLarity OUTPut:RI:MODE [SOURce:]CURRent [SOURce:]CURRent:TRIGger [SOURce:]CURRent:PROTection:STATe [SOURce:]DIGital:DATA [SOURce:]DIGital:FUNCtion [SOURce:]VOLTage [SOURce:]VOLTage:ALC:BANDwidth [SOURce:]VOLTage:ALC:BWIDth [SOURce:]VOLTage:TRIGger [SOURce:]VOLTage:PROTection STATus:PRESet STATus:OPERation STATus:OPERation:CONDition STATus:OPERation:ENABle STATus:OPERation:NTR STATus:OPERation:PTR STATus:QUEStionable STATus:QUEStionable:CONDition STATus:QUEStionable:ENABle STATus:QUEStionable:NTR STATus:QUEStionable:PTR *CLS *ESE *ESR *OPC *PSC *SRE *STB *WAI DISPlay DISPlay:MODE DISPlay:TEXT SYSTem:ERRor SYSTem:LANGuage SYSTem:VERSion SYSTem:LOCal SYSTem:REMote SYSTem:RWLock *IDN *OPT *RCL *RST *SAV *TST ABORt INITiate:SEQuence INITiate:NAME INITiate:CONTinuous:SEQuence1 INITiate:CONTinuous:NAME TRIGger TRIGger:SOURce TRIGger:SEQuence2 TRIGger:ACQuire TRIGger:SEQuence2:COUNt:CURRent TRIGger:ACQuire:COUNt:CURRent TRIGger:SEQuence2:COUNt:VOLTage TRIGger:ACQuire:COUNt:VOLTage TRIGger:SEQuence2:HYSTeresis:CURRent TRIGger:ACQuire:HYSTeresis:CURRent TRIGger:SEQuence2:HYSTeresis:VOLTage TRIGger:ACQuire:HYSTeresis:VOLTage TRIGger:SEQuence2:LEVel:CURRent TRIGger:ACQuire:LEVel:CURRent TRIGger:SEQuence2:LEVel:VOLTage TRIGger:ACQuire:LEVel:VOLTage TRIGger:SEQuence2:SLOPe:CURRent TRIGger:ACQuire:SLOPe:CURRent TRIGger:SEQuence2:SLOPe:VOLTage TRIGger:ACQuire:SLOPe:VOLTage TRIGger:SEQuence2:SOURce TRIGger:ACQuire:SOURce TRIGger:SEQuence1:DEFine TRIGger:SEQuence2:DEFine *TRG Page SCPI Conformance Information SCPI Confirmed Commands Non-SCPICommands Page Compatibility Language Table B-2.COMPatibility Commands Compatibility Similar SCPI Table B-2.COMPatibility Commands (continued) Error Table B-3.COMPatibility Errors NumberError String [Description/Explanation/Examples] Figure B-1.COMpatibility Status Model Table B-4.Bit Assignment of Status, Astatus, Fault, & Mask Registers Page Error Messages Table C-1.Error Numbers (continued) Page Page Example Programs Assigning the GPIB Address in Programs Types of DOS Drivers Error Handling BASIC Controllers Example 1. HP Vectra PC Controller Using Agilent 82335 Interface Page Example 2. IBM Controller Using National Interface Page Example 3. Controller Using BASIC INDEX Page Page Page Manual Updates