B - Compatibility Language |
|
| ||
|
| Table |
|
|
Compatibility |
| Description |
| Similar SCPI |
Command |
|
|
| Command |
ASTS? |
| This command reads the contents of the accumulated status |
| STAT:OPER? |
|
| register, which stores any bit condition entered in the status |
| STAT:QUES? |
|
| register since the accumulated status register was last read, |
| *ESE? |
|
| regardless of whether the condition still exists. |
|
|
|
| Data Representation: ZZZZD |
|
|
CLR |
| This command initializes the dc source to the |
| *RST |
|
| also resets the PON bit in the serial poll register. The command |
|
|
|
| performs the same function as the Device Clear (DCL) interface |
|
|
|
| message. |
|
|
DC 0 1 |
| Only applies to units with Relay Option 760. This command |
| OUTP:STAT[:NOR] |
|
| enables or disables the output without affecting the state of the |
| 0 1 OFF ON |
|
| output relays. |
|
|
|
| Initial condition: DC 1 |
|
|
DLY <n> |
| This command programs the delay time between the programming |
| OUTP:PROT:DEL |
|
| of an output change that produces a CV, CC, or an UNREG |
|
|
|
| condition, and the recording of that condition by the status |
|
|
|
| registers. This can be used to prevent false triggering of the |
|
|
|
| OverCurrent Protection feature (OCP). |
|
|
|
| Initial delay: 0.08s (Normal); 0.008s (Fast). |
|
|
DSP 0 1 |
| This command enables or disables the dc source’s front panel |
| DISP 01OFFON |
|
| display. |
|
|
|
| Initial condition: DSP 1 |
|
|
ERR? |
| This command determines the type of programming error detected |
| SYST:ERR? |
|
| by the dc source. A remote programming error sets the ERR bit in |
|
|
|
| the status register, which can be enabled by UNMASK to request |
|
|
|
| service. |
|
|
FAULT? |
| This command reads which bits have been set in the fault register. |
| STAT:OPER? |
|
| A bit is set in the fault register when the corresponding bit in the |
| STAT:QUES? |
|
| status register changes from inactive to active AND the |
| *ESE |
|
| corresponding bit in the mask register has been enabled. The fault |
|
|
|
| register is reset only after it has been read. The decimal equivalent |
|
|
|
| of the total bit weight of all enabled bits is returned. |
|
|
|
| Data Representation: ZZZZD |
|
|
ID? |
| This command causes the dc source to report its model number |
| *IDN? |
|
| and any options that affect the dc source’s output. |
|
|
|
| Data Representation: Agilent663XA |
|
|
IOUT? |
| This command measures and returns the actual output current. |
| MEAS:CURR? |
|
| Data Representation: SD.DDDD |
|
|
ISET <n> |
| This command programs the output current. See Table |
| CURR |
|
| programming range of this command. |
|
|
|
| Initial condition: see Table |
|
|
OCP 0 1 |
| This command enables or disables the dc source’s overcurrent |
| CURR:PROT:STAT |
|
| protection. If this function is enabled and the dc source goes into |
| 0 1 OFF ON |
|
| CC mode, the output of the dc source is disabled. Initial condition: |
|
|
|
| OCP 0 |
|
|
OUT 0 1 |
| This command enables or disables the dc source’s output. The dc |
| OUTP:STAT |
|
| source will be able to implement commands even while the output |
| 0 1 OFF ON |
|
| is disabled. Initial condition: OUT 1 |
|
|
84