Manuals / Brands / Computer Equipment / Power Supply / HP / Computer Equipment / Power Supply

HP 66332A [SOURce:]DIGital:DATA, [SOURce:]DIGital:FUNCtion, [SOURce:]VOLTage, RIDFi, DIGio, Examples, Examples, Examples, Parameters, Parameters, *RST Value

1 103

Download 103 pages, 546 Kb

Language Dictionary - 4

[SOURce:]DIGital:DATA

This command sets and reads the dc source digital control port when that port is configured for Digital I/O operation. The port has three signal pins and a digital ground pin. Pins 1 and 2 are output pins controlled by bits 0 and 1. Pin 3 is controlled by bit 2, and can be programmed to serve either as an input or an output. It normally serves as an output. Bit 2 must be programmed high to use pin 3 as an input. Pin 4 is the digital ground. The query returns the last programmed value in bits 0 and 1 and the value read at pin 3 in bit 2.

		Program		Bit Configuration				Pin Setting
		Value	2		1	0	4	3	2	1
		0	0		0	0	GND Output		Lo	Lo
		1	0		0	1	GND Output		Lo	Hi
		2	0		1	0	GND Output		Hi	Lo
		3	0		1	1	GND Output		Hi	Hi
		4	1		0	0	GND	Intput	Lo	Lo
		5	1		0	1	GND	Intput	Lo	Hi
		6	1		1	0	GND	Intput	Hi	Lo
		7		1	1	1	GND	Intput	Hi	Hi
Command Syntax				[SOURce]:DIGital:DATA[:VALue] <NRf>
		Parameters		0 to 7
		*RST Value	0
		Examples		DIG:DATA 7
Query Syntax				[SOURce]:DIGital:DATA?
Returned Parameters				<NR1>
Related Commands				DIG:FUNC

[SOURce:]DIGital:FUNCtion

This command configures the dc source digital control port. The configuration setting is saved in non- volatile memory.

RIDFi	Configures the port for Remote Inhibit/Discrete Fault Interrupt operation
DIGio	Configures the port for Digital input/output operation (see DIG:DATA)
	Command Syntax	[SOURce]:DIGital:FUNCtion <CRD>
	Parameters	RIDFi DIGio
	Examples	DIG:FUNC DIG
	Query Syntax	[SOURce]:DIGital:FUNC?
	Returned Parameters	<CRD>
	Related Commands	DIG:DATA

[SOURce:]VOLTage

This command sets the output voltage level of the dc source.

Command Syntax	[SOURce]:VOLTage[:LEVel][:IMMediate][:AMPLitude]<NRf+>
Parameters	see Table 4-3
Default Suffix	V (volts)
*RST Value	0
Examples	VOLT 2	VOLTAGE:LEVEL 200 MV
Query Syntax	[SOURce]:VOLTage[:LEVel][:IMMediate][:AMPLitude]?
Returned Parameters	<NR3>
Related Commands	VOLT:TRIG

59

Contents

Programming Guide Safety Guidelines Printing History 1 - GENERAL INFORMATION 2 - INTRODUCTION TO PROGRAMMING 3 - PROGRAMMING THE DC SOURCE 4 - LANGUAGE DICTIONARY Output Commands Status Commands A - SCPI CONFORMANCE INFORMATION B - COMPATIBILITY LANGUAGE C - ERROR MESSAGES D - EXAMPLE PROGRAMS INDEX General Information GPIB References SCPI References Introduction to Programming Supported Applications System Requirements Downloading and Installing the Driver Accessing Online Help GPIB Address RS-232Data Format RS-232Flow Control RS-232Programming Example RS-232Troubleshooting Conventions Used in This Guide Multiple Commands in a Message Moving Among Subsystems Including Common Commands Using Queries The Message Unit Headers Query Indicator Message Unit Separator Root Specifier Numerical Data Formats Suffixes and Multipliers Response Data Types SCPI Command Completion Using Device Clear Page Programming the DC Source Power-onInitialization Enabling the Output Output Voltage Output Current Output Trigger System Model Setting the Voltage or Current Trigger Levels Initiating the Output Trigger System Generating Triggers Voltage and Current Measurements RMS Measurements (Agilent 66312A, 66332A Only) Minimum and Maximum Measurements (Agilent 66312A, 66332A Only) Current Ranges Returning Measurement Data From the Data Buffer (Agilent 66312A, 66332A Only) Measurement Trigger System Model Initiating the Measurement Trigger System (Agilent 66312A, 66332A Only) Selecting the Measurement Trigger Source (Agilent 66312A, 66332A Only) Generating Measurement Triggers (Agilent 66312A, 66332A Only) Figure 3-3.Trigger Commands Used to Measure Output Pulses Current Detector Pulse Measurement Queries Varying the Voltage or Current Sampling Rate Multiple Measurements (Agilent 66312A, 66332A Only) Pre-eventand Post-eventTriggering (Agilent 66312A, 66332A Only) Pulse Measurement Example (Agilent 66312A, 66332A only) Page Power-OnConditions Operation Status Group Questionable Status Group Standard Event Status Group Status Byte Register Determining the Cause of a Service Interrupt Servicing Operation Status and Questionable Status Events Monitoring Both Phases of a Status Transition Remote Inhibit (RI) Discrete Fault Indicator (DFI) Using the Inhibit/Fault Port as a Digital I/O DFI Programming Example Page Language Dictionary Subsystem Commands Table 4-1.Subsystem Commands Syntax Table 4-1.Subsystem Commands Syntax (continued) Page Common Commands Programming Parameters CALibrate:CURRent CALibrate:CURRent:NEGative CALibrate:CURRent:MEASure:LOWRange CALibrate:CURRent:MEASure:AC CALibrate:DATA CALibrate:LEVel CALibrate:PASSword CALibrate:SAVE CALibrate:STATe CALibrate:VOLTage CALibrate:VOLTage:PROTection MEASure:ARRay:CURRent FETCh:ARRay:CURRent MEASure:ARRay:VOLTage FETCh:ARRay:VOLTage MEASure:CURRent FETCh:CURRent MEASure:CURRent:ACDC FETCh:CURRent:ACDC MEASure:CURRent:HIGH MEASure:CURRent:LOW FETCh:CURRent:LOW MEASure:CURRent:MAXimum FETCh:CURRent: MAXimum MEASure:CURRent:MINimum MEASure:VOLTage FETCh:VOLTage MEASure:VOLTage:ACDC FETCh:VOLTage:ACDC MEASure:VOLTage:HIGH MEASure:VOLTage:LOW FETCh:VOLTage:LOW MEASure:VOLTage:MAXimum FETCh:VOLTage:MAXimum MEASure:VOLTage:MINimum SENSe:CURRent:RANGe SENSe:CURRent:DETector SENSe:FUNCtion SENSe:SWEep:OFFSet:POINts SENSe:SWEep:POINts SENSe:SWEep:TINTerval SENSe:WINDow OUTPut OUTPut:DFI OUTPut:DFI:SOURce OUTPut:PON:STATe OUTPut:PROTection:CLEar OUTPut:PROTection:DELay OUTPut:RELay OUTPut:RELay:POLarity OUTPut:RI:MODE [SOURce:]CURRent [SOURce:]CURRent:TRIGger [SOURce:]CURRent:PROTection:STATe [SOURce:]DIGital:DATA [SOURce:]DIGital:FUNCtion [SOURce:]VOLTage [SOURce:]VOLTage:ALC:BANDwidth [SOURce:]VOLTage:ALC:BWIDth [SOURce:]VOLTage:TRIGger [SOURce:]VOLTage:PROTection STATus:PRESet STATus:OPERation STATus:OPERation:CONDition STATus:OPERation:ENABle STATus:OPERation:NTR STATus:OPERation:PTR STATus:QUEStionable STATus:QUEStionable:CONDition STATus:QUEStionable:ENABle STATus:QUEStionable:NTR STATus:QUEStionable:PTR *CLS *ESE *ESR *OPC *PSC *SRE *STB *WAI DISPlay DISPlay:MODE DISPlay:TEXT SYSTem:ERRor SYSTem:LANGuage SYSTem:VERSion SYSTem:LOCal SYSTem:REMote SYSTem:RWLock *IDN *OPT *RCL *RST *SAV *TST ABORt INITiate:SEQuence INITiate:NAME INITiate:CONTinuous:SEQuence1 INITiate:CONTinuous:NAME TRIGger TRIGger:SOURce TRIGger:SEQuence2 TRIGger:ACQuire TRIGger:SEQuence2:COUNt:CURRent TRIGger:ACQuire:COUNt:CURRent TRIGger:SEQuence2:COUNt:VOLTage TRIGger:ACQuire:COUNt:VOLTage TRIGger:SEQuence2:HYSTeresis:CURRent TRIGger:ACQuire:HYSTeresis:CURRent TRIGger:SEQuence2:HYSTeresis:VOLTage TRIGger:ACQuire:HYSTeresis:VOLTage TRIGger:SEQuence2:LEVel:CURRent TRIGger:ACQuire:LEVel:CURRent TRIGger:SEQuence2:LEVel:VOLTage TRIGger:ACQuire:LEVel:VOLTage TRIGger:SEQuence2:SLOPe:CURRent TRIGger:ACQuire:SLOPe:CURRent TRIGger:SEQuence2:SLOPe:VOLTage TRIGger:ACQuire:SLOPe:VOLTage TRIGger:SEQuence2:SOURce TRIGger:ACQuire:SOURce TRIGger:SEQuence1:DEFine TRIGger:SEQuence2:DEFine *TRG Page SCPI Conformance Information SCPI Confirmed Commands Non-SCPICommands Page Compatibility Language Table B-2.COMPatibility Commands Compatibility Similar SCPI Table B-2.COMPatibility Commands (continued) Error Table B-3.COMPatibility Errors NumberError String [Description/Explanation/Examples] Figure B-1.COMpatibility Status Model Table B-4.Bit Assignment of Status, Astatus, Fault, & Mask Registers Page Error Messages Table C-1.Error Numbers (continued) Page Page Example Programs Assigning the GPIB Address in Programs Types of DOS Drivers Error Handling BASIC Controllers Example 1. HP Vectra PC Controller Using Agilent 82335 Interface Page Example 2. IBM Controller Using National Interface Page Example 3. Controller Using BASIC INDEX Page Page Page Manual Updates