Table |
|
|
Task | Section | |
□ For a newly installed system disk, you can back up the disk. (At this | Section 7.2 (page 115) | |
point, you could reinstall OpenVMS onto the disk instead.) |
| |
For a newly upgraded system disk, if it is not going to be a shadow set |
| |
member, back up the system disk as a safeguard before proceeding |
| |
with the next steps. If your newly upgraded system disk is going to |
| |
be a shadow set member, you can |
| |
optional precaution, you can back up the system disk as well. |
| |
□ Register any licenses that were not registered during the installation; | Section 7.3 (page 116) | |
for an upgrade, register any new licenses. |
| |
□ New installations only (optional): Set system parameters to enable volume | Section 7.4 (page 117) | |
shadowing. |
| |
□ If you set system parameters to enable volume shadowing or removed | Section 7.5 (page 118) | |
hardcoded BAP system parameters, run AUTOGEN and reboot. |
| |
□ If you want to form a shadow set for a newly installed system disk, | Section 7.6 (page 118) | |
you can do this now or later. If you upgraded a disk in a volume |
| |
shadowing environment, |
| |
□ New installations, some upgrades: Perform the following tasks that |
| |
generally apply to new installations only but could also apply after an |
| |
upgrade: |
| |
□ Create proxy files, if required. | Section 7.7.1 (page 120) | |
□ Set up the queue manager and start the default batch and print | Section 7.7.2 (page 120) | |
| queues. |
|
□ Configure a multihead system, if applicable. | Section 7.7.3 (page 121) | |
□ Configure DECnet if it was installed. After an upgrade, perform | Section 7.7.4 (page 121) | |
| only if DECnet was added during the upgrade. |
|
□ Configure TCP/IP Services for OpenVMS if it was installed. After | Section 7.7.5 (page 122) | |
| an upgrade, configure TCP/IP Services only if it was added during |
|
| the upgrade. |
|
□ If you are using neither DECnet nor TCP/IP Services, install and | Section 7.7.6 (page 122) | |
| configure |
|
| Networking software is required to download patches and for |
|
| certain layered products. |
|
□ Initialize or configure the following products, as needed: |
| |
□ | Initialize CDSA. | Section 7.8.1 (page 123) |
□ | Configure Availability Manager. | Section 7.8.2 (page 124) |
□ | Configure Kerberos. | Section 7.8.3 (page 125) |
□ Configure SSL for OpenVMS. | Section 7.8.4 (page 126) | |
□ On Integrity servers using services that depend on WBEM Services | Section 7.8.5 (page 127) | |
| for OpenVMS, configure WBEM Services for OpenVMS. |
|
□ On Integrity servers using services that depend on WBEM | Section 7.8.6 (page 131) | |
| Providers, configure WBEM Providers for OpenVMS. |
|
□ On Integrity servers that use Instant Capacity (iCAP) or Temporary | Section 7.8.7 (page 132) | |
| Instant Capacity (TiCAP), configure the iCAP software. |
|
□ On Integrity servers that use Pay per use (PPU), configure the | Section 7.8.8 (page 132) | |
| PPU software. |
|
114 After Installing or Upgrading the OpenVMS Operating System