HP OpenVMS 8.x manual Next Steps, Blk1 AcpiHWP0002,100/Pci10/ScsiPun0,Lun0

Loading.: EFI Shell [Built-in]

	EFI Shell version 1.10 [14.61]
	Device mapping table
fs	fs0 : Acpi(HWP0002,100)/Pci(10)/Scsi(Pun0,Lun0)/HD(Part1,Sig8FCF6F11-...
	fs1 : Acpi(HWP0002,100)/Pci(10)/Scsi(Pun0,Lun0)/HD(Part4,Sig8FCF6F10-...)
	blk0 : Acpi(HWP0002,0)/Pci(20)/Ata(Primary,Master)
	blk1 : Acpi(HWP0002,100)/Pci(10)/Scsi(Pun0,Lun0)
blk	blk2 : Acpi(HWP0002,100)/Pci(10)/Scsi(Pun0,Lun0)/HD(Part1,Sig8FCF6F11-...)
	blk3 : Acpi(HWP0002,100)/Pci(10)/Scsi(Pun0,Lun0)/HD(Part2,Sig8FCF6F10-...)
	blk4 : Acpi(HWP0002,100)/Pci(10)/Scsi(Pun0,Lun0)/HD(Part3,Sig8FCF6F11-...)
	blk5 : Acpi(HWP0002,100)/Pci(10)/Scsi(Pun0,Lun0)/HD(Part4,Sig8FCF6F10-...)
	blk6 : Acpi(HWP0002,100)/Pci(10)/Scsi(Pun0,Lun0)/HD(Part5,Sig8FCF6F10-...)
	Shell>
fs	The fs devices are file-structured logical partitions on physical disks that
	are included with your Integrity server system. One or more fs device
	exists for each volume with a bootable partition or diagnostic partition.
	Generally, fs0: corresponds to the target disk on which you installed
	OpenVMS I64 (unless the DVD was not removed, in which case fs1:
	corresponds to the target disk). For example, if the target disk is DKA0,
	then fs0: most likely corresponds to the target disk. On the other hand,
	if the target disk is a DKA100 or DKB200 or similar, the corresponding
	EFI device depends on what partitions are configured on the target disk.
blk	The blk devices are block devices. Multiple blk devices exist for each
	volume that has a bootable partition or diagnostic partition. These devices
	may include the DVD device as well as the diagnostic partitions on
	OpenVMS system disks. Diagnostic partitions are intended and reserved
	for use by HP Services. (For more information about this partition, see
	Appendix I (page 269).)

3.To boot the OpenVMS I64 system disk, enter the following command at the EFI Shell prompt, where fsn: is the device associated with the system disk (probably fs0:):

Shell> fsn:\efi\vms\vms_loader.efi

The OpenVMS I64 operating system now starts booting. A display similar to the following appears, followed by the prompt for user name and password:

HP OpenVMS Industry Standard 64 Operating System, Version 8.3-1H1

(c) Copyright 1976-2006 Hewlett-Packard Development Company, L.P.

Note that HP Integrity servers maintain a system event log (SEL) within system console storage, and OpenVMS I64 automatically transfers the contents of the SEL into the OpenVMS error log. On certain machines, during a successful boot operation while using a console, you might see a message indicating that the Baseboard Management Controller (BMC) SEL is full. You can safely continue when the BMC SEL is full by following the prompts; OpenVMS processes the contents of the SEL.

3.4.2 Next Steps

When you boot OpenVMS from a new system disk, a special startup procedure runs that does the following:

•Gives you the opportunity to configure the system for standalone or OpenVMS Cluster operation (see Section 3.5 (page 74)).

•Runs AUTOGEN to evaluate your hardware configuration, estimate typical workloads, and set system parameters (see Section 3.6 (page 75)).

•Reboots your system with the new parameters (see Section 3.7 (page 75)).

After the system is rebooted with the new parameters, you can log into your SYSTEM account, as explained in Section 3.8 (page 76). On Integrity servers, if you did not allow the OpenVMS installation procedure to create a boot option for your system disk, you can set up such an option

3.4 Booting the New OpenVMS System Disk 73