HP RTEA manual

*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%*

*

*

*RTE–A Sample System Generation Answer File

************************************************************************

*	*						*
*	*	This half of the Primary answer file is designed to be edited					*
*	*	and	used for a system–specific generation. To use this file,				*
*	*	first delete the first half of this file, then uncomment the					*
*	*	required lines (marked with a ”*!”) and any specific system					*
*	*	modules required by removing the appropriate comment character.					*
*	*						*
*	*	For	further information, refer to the RTE–A System Generation				*
*	*	and	Installation Manual, part no. 92077–90034.				*
*	*						*
*	*	1.	Uncomment all required modules by removing the string				*
*	*		”*!REMOVE!”.	Refer to the EDIT/1000 User’s Guide, part no.			*
*	*		92074–90001, and the note at the bottom of these instructions *
*	*		for information on how to use EDIT/1000 to edit this file.				*
*	*						*
*	*	2.	To select your system disk, remove *!REMOVESCSI! for SCSI				*
*	*		disk, remove *!REMOVEHPIB! and *!REMOVEHPIB64! for 64MB HP–IB *
*	*		disk, or remove *!REMOVEHPIB! and *!REMOVEHPIB20! for 20MB				*
*	*		HP–IB disk.				*
*	*						*
*	*	3.	If you want VC+ in your system, uncomment all VC+ modules				*
*	*		by removing the string ”*!YESVC+!”;			otherwise uncomment	*
*	*		the non–VC+ modules by removing the string ”*!NO_VC+!”.				*
*	*		VC+ is supplied with the HP 92078A Virtual Code+ package,				*
*	*		a product which allows a multiuser environment and spooling.				*
*	*						*
*	*	4.	If you have NS/1000 and LAN/1000 in your system, uncomment				*
*	*		all NS/1000 and LAN/1000 modules by removing the string				*
*	*		”*!YES_NS!”;	otherwise, uncomment the non–NS modules by			*
*	*		removing the string ”*!NO__NS!”.		If you have NS/1000 but not *
*	*		LAN/1000 in your system, refer to the NS subsystems’ answer				*
*	*		file.				*
*	*						*
*	*	5.	If you have APRA/1000 in your system, rename the ”NS1000”				*
*	*		directory to ”APRA1000” and comment the %adv00 driver and LU				*
*	*		mapping (lu 81 – 82) out.				*
*	*						*
*	*	6.	If you do not use an ASIC card as LU 1 (as generated in				*
*	*		this system) comment it out and change one of the				*
*	*		terminal LUs generated into the system (such as the				*
*	*		8–channel multiplexer) as LU 1.				*
*	*						*
*	*	7.	Uncomment the ”*” before the RPL file you will be using				*
*	*		according to your hardware configuration. If you are using				*
*	*		the A600 (not the A600+), i.e., %RPL60, you will need to				*
*	*		remove the string ”*!RPL60_!”.		If you are using the A900 and *
*	*		NS/1000, choose %RPL91 then either rpl_a900_rev4.rel (rev.4				*
*	*		firmware or later) or xmb.rel (pre rev.4 firmware).				*
*	*						*
*	*	8.	If you don’t have NS/1000 in your system and you want to use				*
*	*		the DDC00/DDC01 modem handler, HPMDM.RUN, uncomment the				*
*	*		”*!YES_NS!” before HPMDM_TABLE.REL.			If you want to save	*