Manuals / Huffy / Fitness & Sports / Board Games

Huffy Sports Basketball Systems manual

Models: Sports Basketball Systems

1 28

Download 28 pages 57.72 Kb

Page 26

Image 26

IMPORTANT!:

WAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEPS. CONCRETE MUST CURE.

22.After concrete has cured, remove tape, install pole cap (40), fit pole assembly into sleeve (4).

IMPORTANT! Position pole assembly so the elevator assembly is perpendicular with playing surface.

IMPORTANT! The elevator holes MUST be parallel with playing surface.

WARNING

TWO PERSON MINIMUM REQUIRED

FOR THIS PROCEDURE. NOT

FOLLOWING RECOMMENDATION

MAY RESULT IN SERIOUS BODILY

INJURY AND/OR PROPERTY

DAMAGE.

PLAYING SURFACE

23.Use wedge to tap cap of ground sleeve until tight.

P/N 21145507 02/04

Page 26

Image 26

Huffy Sports Basketball Systems manual IMPORTANT! The elevator holes MUST be parallel with playing surface

Contents

Inground System Owners Manual Customer Service CenterToll-Free Customer Service Number for U.S For Canada N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.ABEFORE YOU START Do not slide, climb, shake or play on pole Owner must ensure that all players know and followthese rules for safe operation of the system P/N 21145507 02/04 SAFETY INSTRUCTIONSHEIGHT ADJUSTMENT Remove all contents from boxes NOTICE TO ASSEMBLERSPARTS LIST - See Hardware Identifier Item #36 HARDWARE IDENTIFIER BOLTS & SCREWSItem #23 Item #8 Item #27 1 Item #16 Item #12 Item #24 Item #31 HARDWARE IDENTIFIER NUTS & WASHERS2 Socket Wrenches and Sockets 1/2” 9/16” AND SECTION A ASSEMBLE THE POLE2 1/2”, 2 9/16” AND 2 3/4” Wrenches AND/OR a Phillips-Head ScrewdriverCONTACT UTILITIES BEFORE DIGGING MIDDLEBOTTOM Tape Not SuppliedFLANGE FIG. AFIG. B FIG. C SIDE VIEWNote B SIDE VIEWNote A Note A7. Install ground sleeve cap 5 onto 10. Attach spacers 10, 11 to pole mount bracket 7 with bolts 12, washers 13, and nuts 14 as shown. IMPORTANT! Tighten until washers 13 no longer move to prevent labels from being damaged during height adjustment SIDE ACCESSIndicator labels should be applied as close to holes as possible as 20 shown in illustration2 1/2, 2 9/16” AND 2 3/4” Wrenches AND/OR SECTION B ASSEMBLE THE BACKBOARD TO ELEVATOR TUBESASSEMBLY WILL VARY DUE TO BACKBOARD STYLE 2 Socket Wrenches and Sockets1B. Assemble elevator tubes 30 as shown. Tighten completely 2B. Assemble elevator tubes 30 as shown. Tighten completely Use the following assembly instructions if you have a48 molded plastic backboard Fan 02/04Instructions Included With Backboard Hardware For Board Assembly a 44” steel-framed acrylic backboardUse the following assembly instructions if you have a 3A. Assemble backboard brackets to board as shown Refer ToInstructions AssemblyRefer To Included With RimInstall spacers 25, and springs 39 onto backboard 48” molded plastic-framed acrylic backboardUse the following assembly instructions if you have a 2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets SECTION C ATTACH THE BACKBOARD/ELEVATOR TO POLE SYSTEMBACKBOARD WILL VARY 3/4”17. Install handle assembly to long CONCRETE MUST CURE USE EYE PROTECTION WHEN INSTALLING SPRINGSWAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEP22 Page 02/04 NET INSTALLATIONInsert net into bottom of clip as shown IMPORTANT! The elevator holes MUST be parallel with playing surface Note A NOTE A Do not use washers here on spring return style rimNOTE A Do not use washers here on spring return style rim Note AB. Move elevator up or down to desired height B C A25. A. While holding handle, remove pin C. Replace pin 26 full length to lock system at desired height