Manuals / Huffy / Fitness & Sports / Board Games

Huffy Sports Basketball Systems manual Notice To Assemblers, Remove all contents from boxes

Models: Sports Basketball Systems

1 28

Page 5

NOTICE TO ASSEMBLERS

ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.

IMPORTANT!

Remove all contents from boxes.

Be sure to check inside pole sections; hardware and additional parts are packed inside.

WARRANTY CARD:

Please remember to complete your product registration form either on-line at: www.huffysports.com or mail-in the enclosed postcard.

For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com.

02/04

P/N 21145507

Page 5

Image 5

Contents

Toll-Free Customer Service Number for U.S For Canada Customer Service CenterInground System Owners Manual N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.ABEFORE YOU START Do not slide, climb, shake or play on pole Owner must ensure that all players know and followthese rules for safe operation of the system P/N 21145507 02/04 SAFETY INSTRUCTIONSHEIGHT ADJUSTMENT NOTICE TO ASSEMBLERS Remove all contents from boxesPARTS LIST - See Hardware Identifier Item #23 Item #8 Item #27 1 Item #16 Item #12 Item #24 Item #31 HARDWARE IDENTIFIER BOLTS & SCREWSItem #36 HARDWARE IDENTIFIER NUTS & WASHERS2 1/2”, 2 9/16” AND 2 3/4” Wrenches AND/OR SECTION A ASSEMBLE THE POLE2 Socket Wrenches and Sockets 1/2” 9/16” AND a Phillips-Head ScrewdriverBOTTOM MIDDLECONTACT UTILITIES BEFORE DIGGING Tape Not SuppliedFIG. B FIG. C FIG. AFLANGE SIDE VIEWNote A SIDE VIEWNote B Note A7. Install ground sleeve cap 5 onto 10. Attach spacers 10, 11 to pole mount bracket 7 with bolts 12, washers 13, and nuts 14 as shown. IMPORTANT! Tighten until washers 13 no longer move Indicator labels should be applied as close to holes as possible as SIDE ACCESSto prevent labels from being damaged during height adjustment 20 shown in illustrationASSEMBLY WILL VARY DUE TO BACKBOARD STYLE SECTION B ASSEMBLE THE BACKBOARD TO ELEVATOR TUBES2 1/2, 2 9/16” AND 2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets1B. Assemble elevator tubes 30 as shown. Tighten completely 48 molded plastic backboard Fan Use the following assembly instructions if you have a2B. Assemble elevator tubes 30 as shown. Tighten completely 02/04Use the following assembly instructions if you have a a 44” steel-framed acrylic backboardInstructions Included With Backboard Hardware For Board Assembly 3A. Assemble backboard brackets to board as shown Refer ToRefer To AssemblyInstructions Included With RimInstall spacers 25, and springs 39 onto backboard 48” molded plastic-framed acrylic backboardUse the following assembly instructions if you have a BACKBOARD WILL VARY SECTION C ATTACH THE BACKBOARD/ELEVATOR TO POLE SYSTEM2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets 3/4”17. Install handle assembly to long CONCRETE MUST CURE USE EYE PROTECTION WHEN INSTALLING SPRINGSWAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEP22 Page 02/04 NET INSTALLATIONInsert net into bottom of clip as shown IMPORTANT! The elevator holes MUST be parallel with playing surface NOTE A Do not use washers here on spring return style rim NOTE A Do not use washers here on spring return style rimNote A Note A25. A. While holding handle, remove pin B C AB. Move elevator up or down to desired height C. Replace pin 26 full length to lock system at desired height