Manuals / Huffy / Fitness & Sports / Board Games

Huffy Sports Basketball Systems manual 48” molded plastic-framed acrylic backboard

Models: Sports Basketball Systems

1 28

Download 28 pages 57.72 Kb

Page 20

48” molded plastic-framed acrylic backboard.

Use the following assembly instructions if you have a

48” molded plastic-framed acrylic backboard.

Install spacers (25), and springs (39) onto backboard

4A. brackets (26) with bolts (27, 36), washers (37) and lock-nuts (14, 28) as shown. Bend bracket (26) to line up with holes in backboard.

28 26

14

25

27

12

4B. Assemble elevator tubes (30) as shown. Tighten completely.

IMPORTANT!:

29

26

32

31

29

33

33

35

32

35

It is necessary for all parts to be instaslled for this mechanism to work safely and properly.

30

31

39 30

P/N 21145507 02/04

20

Image 20

Huffy Sports Basketball Systems manual 48” molded plastic-framed acrylic backboard

Contents

Customer Service Center Toll-Free Customer Service Number for U.S For CanadaInground System Owners Manual N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.ABEFORE YOU START Do not slide, climb, shake or play on pole Owner must ensure that all players know and followthese rules for safe operation of the system P/N 21145507 02/04 SAFETY INSTRUCTIONSHEIGHT ADJUSTMENT Remove all contents from boxes NOTICE TO ASSEMBLERSPARTS LIST - See Hardware Identifier HARDWARE IDENTIFIER BOLTS & SCREWS Item #23 Item #8 Item #27 1 Item #16 Item #12 Item #24 Item #31Item #36 HARDWARE IDENTIFIER NUTS & WASHERSSECTION A ASSEMBLE THE POLE 2 1/2”, 2 9/16” AND 2 3/4” Wrenches AND/OR2 Socket Wrenches and Sockets 1/2” 9/16” AND a Phillips-Head ScrewdriverMIDDLE BOTTOMCONTACT UTILITIES BEFORE DIGGING Tape Not SuppliedFIG. A FIG. B FIG. CFLANGE SIDE VIEWSIDE VIEW Note ANote B Note A7. Install ground sleeve cap 5 onto 10. Attach spacers 10, 11 to pole mount bracket 7 with bolts 12, washers 13, and nuts 14 as shown. IMPORTANT! Tighten until washers 13 no longer move SIDE ACCESS Indicator labels should be applied as close to holes as possible asto prevent labels from being damaged during height adjustment 20 shown in illustrationSECTION B ASSEMBLE THE BACKBOARD TO ELEVATOR TUBES ASSEMBLY WILL VARY DUE TO BACKBOARD STYLE2 1/2, 2 9/16” AND 2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets1B. Assemble elevator tubes 30 as shown. Tighten completely Use the following assembly instructions if you have a 48 molded plastic backboard Fan2B. Assemble elevator tubes 30 as shown. Tighten completely 02/04a 44” steel-framed acrylic backboard Use the following assembly instructions if you have aInstructions Included With Backboard Hardware For Board Assembly 3A. Assemble backboard brackets to board as shown Refer ToAssembly Refer ToInstructions Included With RimInstall spacers 25, and springs 39 onto backboard 48” molded plastic-framed acrylic backboardUse the following assembly instructions if you have a SECTION C ATTACH THE BACKBOARD/ELEVATOR TO POLE SYSTEM BACKBOARD WILL VARY2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets 3/4”17. Install handle assembly to long CONCRETE MUST CURE USE EYE PROTECTION WHEN INSTALLING SPRINGSWAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEP22 Page 02/04 NET INSTALLATIONInsert net into bottom of clip as shown IMPORTANT! The elevator holes MUST be parallel with playing surface NOTE A Do not use washers here on spring return style rim NOTE A Do not use washers here on spring return style rimNote A Note AB C A 25. A. While holding handle, remove pinB. Move elevator up or down to desired height C. Replace pin 26 full length to lock system at desired height