Manuals / Huffy / Fitness & Sports / Board Games

Huffy Sports Basketball Systems manual

Models: Sports Basketball Systems

1 28

Download 28 pages 57.72 Kb

Page 24

Image 24

20.Install clips.

WARNING!

USE OF THIS PRODUCT

WITHOUT PROPER

INSTALLATION OF

SMART CLIPS, OR WHEN

ALL SMART CLIPS ARE

NOT PRESENT COULD

RESULT IN BODILY

HARM. BE SURE TO

FOLLOW DIRECTIONS

CAREFULLY.

CLIP “ARM”

CLIP “BODY”

Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown.

Push in direction indicated by arrows.

Push second “arm” back and into ram as shown.

Twist “body” of clip slightly again to spread “arms” of clip. Clip “arms” must be flat and touching edge to edge as shown, not overlapping.

P/N 21145507 02/04

Page 24

Image 24

Contents

Customer Service Center Toll-Free Customer Service Number for U.S For CanadaInground System Owners Manual N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.ABEFORE YOU START Owner must ensure that all players know and follow these rules for safe operation of the systemDo not slide, climb, shake or play on pole SAFETY INSTRUCTIONS HEIGHT ADJUSTMENTP/N 21145507 02/04 Remove all contents from boxes NOTICE TO ASSEMBLERSPARTS LIST - See Hardware Identifier HARDWARE IDENTIFIER BOLTS & SCREWS Item #23 Item #8 Item #27 1 Item #16 Item #12 Item #24 Item #31Item #36 HARDWARE IDENTIFIER NUTS & WASHERSSECTION A ASSEMBLE THE POLE 2 1/2”, 2 9/16” AND 2 3/4” Wrenches AND/OR2 Socket Wrenches and Sockets 1/2” 9/16” AND a Phillips-Head ScrewdriverMIDDLE BOTTOMCONTACT UTILITIES BEFORE DIGGING Tape Not SuppliedFIG. A FIG. B FIG. CFLANGE SIDE VIEWSIDE VIEW Note ANote B Note A7. Install ground sleeve cap 5 onto 10. Attach spacers 10, 11 to pole mount bracket 7 with bolts 12, washers 13, and nuts 14 as shown. IMPORTANT! Tighten until washers 13 no longer move SIDE ACCESS Indicator labels should be applied as close to holes as possible asto prevent labels from being damaged during height adjustment 20 shown in illustrationSECTION B ASSEMBLE THE BACKBOARD TO ELEVATOR TUBES ASSEMBLY WILL VARY DUE TO BACKBOARD STYLE2 1/2, 2 9/16” AND 2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets1B. Assemble elevator tubes 30 as shown. Tighten completely Use the following assembly instructions if you have a 48 molded plastic backboard Fan2B. Assemble elevator tubes 30 as shown. Tighten completely 02/04a 44” steel-framed acrylic backboard Use the following assembly instructions if you have aInstructions Included With Backboard Hardware For Board Assembly 3A. Assemble backboard brackets to board as shown Refer ToAssembly Refer ToInstructions Included With Rim48” molded plastic-framed acrylic backboard Use the following assembly instructions if you have aInstall spacers 25, and springs 39 onto backboard SECTION C ATTACH THE BACKBOARD/ELEVATOR TO POLE SYSTEM BACKBOARD WILL VARY2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets 3/4”17. Install handle assembly to long USE EYE PROTECTION WHEN INSTALLING SPRINGS WAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEP22CONCRETE MUST CURE Page NET INSTALLATION Insert net into bottom of clip as shown02/04 IMPORTANT! The elevator holes MUST be parallel with playing surface NOTE A Do not use washers here on spring return style rim NOTE A Do not use washers here on spring return style rimNote A Note AB C A 25. A. While holding handle, remove pinB. Move elevator up or down to desired height C. Replace pin 26 full length to lock system at desired height