Manuals / Huffy / Fitness & Sports / Board Games

Huffy Sports Basketball Systems Middle, Bottom, Contact Utilities Before Digging, 24 61 cm, 02/04

Models: Sports Basketball Systems

1 28

Download 28 pages 57.72 Kb

Page 9

MIDDLE

1.Mark pole sections with tape (not supplied) at indicated distances from ends as shown.

1

TOP

2

MIDDLE

Tape (Not Supplied)

BOTTOM

3

2.Ensure ground is level with playing surface, then dig pole hole.

WARNING!

CONTACT UTILITIES

BEFORE DIGGING.

Note

GROUND SURFACE

Maximum distance from edge

of hole to edge of playing

surface 6” (15.2 cm).

18" (42.7 cm) 6" (15.2 cm)

PLAYING SURFACE

24" (61 cm)

9

02/04

P/N 21145507

Image 9

Huffy Sports Basketball Systems Middle, Bottom, Contact Utilities Before Digging, Tape Not Supplied, 18 42.7 cm 6 15.2 cm

Contents

Toll-Free Customer Service Number for U.S For Canada Customer Service CenterInground System Owners Manual N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.ABEFORE YOU START Owner must ensure that all players know and follow these rules for safe operation of the systemDo not slide, climb, shake or play on pole SAFETY INSTRUCTIONS HEIGHT ADJUSTMENTP/N 21145507 02/04 NOTICE TO ASSEMBLERS Remove all contents from boxesPARTS LIST - See Hardware Identifier Item #23 Item #8 Item #27 1 Item #16 Item #12 Item #24 Item #31 HARDWARE IDENTIFIER BOLTS & SCREWSItem #36 HARDWARE IDENTIFIER NUTS & WASHERS2 1/2”, 2 9/16” AND 2 3/4” Wrenches AND/OR SECTION A ASSEMBLE THE POLE2 Socket Wrenches and Sockets 1/2” 9/16” AND a Phillips-Head ScrewdriverBOTTOM MIDDLECONTACT UTILITIES BEFORE DIGGING Tape Not SuppliedFIG. B FIG. C FIG. AFLANGE SIDE VIEWNote A SIDE VIEWNote B Note A7. Install ground sleeve cap 5 onto 10. Attach spacers 10, 11 to pole mount bracket 7 with bolts 12, washers 13, and nuts 14 as shown. IMPORTANT! Tighten until washers 13 no longer move Indicator labels should be applied as close to holes as possible as SIDE ACCESSto prevent labels from being damaged during height adjustment 20 shown in illustrationASSEMBLY WILL VARY DUE TO BACKBOARD STYLE SECTION B ASSEMBLE THE BACKBOARD TO ELEVATOR TUBES2 1/2, 2 9/16” AND 2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets1B. Assemble elevator tubes 30 as shown. Tighten completely 48 molded plastic backboard Fan Use the following assembly instructions if you have a2B. Assemble elevator tubes 30 as shown. Tighten completely 02/04Use the following assembly instructions if you have a a 44” steel-framed acrylic backboardInstructions Included With Backboard Hardware For Board Assembly 3A. Assemble backboard brackets to board as shown Refer ToRefer To AssemblyInstructions Included With Rim48” molded plastic-framed acrylic backboard Use the following assembly instructions if you have aInstall spacers 25, and springs 39 onto backboard BACKBOARD WILL VARY SECTION C ATTACH THE BACKBOARD/ELEVATOR TO POLE SYSTEM2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets 3/4”17. Install handle assembly to long USE EYE PROTECTION WHEN INSTALLING SPRINGS WAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEP22CONCRETE MUST CURE Page NET INSTALLATION Insert net into bottom of clip as shown02/04 IMPORTANT! The elevator holes MUST be parallel with playing surface NOTE A Do not use washers here on spring return style rim NOTE A Do not use washers here on spring return style rimNote A Note A25. A. While holding handle, remove pin B C AB. Move elevator up or down to desired height C. Replace pin 26 full length to lock system at desired height