Manuals / Huffy / Fitness & Sports / Board Games

Huffy Sports Basketball Systems Hardware Identifier Bolts & Screws, Item #36, Item #10, Item #25

Models: Sports Basketball Systems

1 28

Download 28 pages 57.72 Kb

Page 7

Image 7

HARDWARE IDENTIFIER (BOLTS & SCREWS)

Item #23 (1)

Item #8 (2)

Item #27 (1) Item #16 (1)

Item #12 (3)

Item #24 (2)

Item #31 (6)

Item #36 (1)

HARDWARE IDENTIFIER (NUTS & WASHERS)

Item #14 (3)

Item #9 (5)

Item #37 (2)

Item #35 (6)

Item #28 (1)

Item #13 (4)

HARDWARE IDENTIFIER (STEEL SPACERS)

Item #10 (2)

Item #25 (4)

HARDWARE IDENTIFIER (PLASTIC SPACERS)

Item #33 (12)

Item #11 (2)

Item #32 (2)

* You may have extra parts with this model.

02/04

P/N 21145507

Page 7

Image 7

Huffy Sports Basketball Systems Hardware Identifier Bolts & Screws, Item #36, Hardware Identifier Nuts & Washers, Item #10

Contents

N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A Customer Service CenterToll-Free Customer Service Number for U.S For Canada Inground System Owners ManualBEFORE YOU START these rules for safe operation of the system Owner must ensure that all players know and followDo not slide, climb, shake or play on pole HEIGHT ADJUSTMENT SAFETY INSTRUCTIONSP/N 21145507 02/04 NOTICE TO ASSEMBLERS Remove all contents from boxesPARTS LIST - See Hardware Identifier HARDWARE IDENTIFIER NUTS & WASHERS HARDWARE IDENTIFIER BOLTS & SCREWSItem #23 Item #8 Item #27 1 Item #16 Item #12 Item #24 Item #31 Item #36a Phillips-Head Screwdriver SECTION A ASSEMBLE THE POLE2 1/2”, 2 9/16” AND 2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets 1/2” 9/16” ANDTape Not Supplied MIDDLEBOTTOM CONTACT UTILITIES BEFORE DIGGINGSIDE VIEW FIG. AFIG. B FIG. C FLANGENote A SIDE VIEWNote A Note B7. Install ground sleeve cap 5 onto 10. Attach spacers 10, 11 to pole mount bracket 7 with bolts 12, washers 13, and nuts 14 as shown. IMPORTANT! Tighten until washers 13 no longer move 20 shown in illustration SIDE ACCESSIndicator labels should be applied as close to holes as possible as to prevent labels from being damaged during height adjustment2 Socket Wrenches and Sockets SECTION B ASSEMBLE THE BACKBOARD TO ELEVATOR TUBESASSEMBLY WILL VARY DUE TO BACKBOARD STYLE 2 1/2, 2 9/16” AND 2 3/4” Wrenches AND/OR1B. Assemble elevator tubes 30 as shown. Tighten completely 02/04 Use the following assembly instructions if you have a48 molded plastic backboard Fan 2B. Assemble elevator tubes 30 as shown. Tighten completely3A. Assemble backboard brackets to board as shown Refer To a 44” steel-framed acrylic backboardUse the following assembly instructions if you have a Instructions Included With Backboard Hardware For Board AssemblyIncluded With Rim AssemblyRefer To InstructionsUse the following assembly instructions if you have a 48” molded plastic-framed acrylic backboardInstall spacers 25, and springs 39 onto backboard 3/4” SECTION C ATTACH THE BACKBOARD/ELEVATOR TO POLE SYSTEMBACKBOARD WILL VARY 2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets17. Install handle assembly to long WAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEP22 USE EYE PROTECTION WHEN INSTALLING SPRINGSCONCRETE MUST CURE Page Insert net into bottom of clip as shown NET INSTALLATION02/04 IMPORTANT! The elevator holes MUST be parallel with playing surface Note A NOTE A Do not use washers here on spring return style rimNOTE A Do not use washers here on spring return style rim Note AC. Replace pin 26 full length to lock system at desired height B C A25. A. While holding handle, remove pin B. Move elevator up or down to desired height