Manuals / Huffy / Fitness & Sports / Board Games

Huffy Sports Basketball Systems manual Inground System Owners Manual, Customer Service Center

Models: Sports Basketball Systems

1 28

Download 28 pages 57.72 Kb

Page 1

Inground System

Inground System

Owners Manual

Customer Service Center

• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.

WARNING!

READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT.

FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY.

REQUIRED TOOLS AND MATERIALS:

•Two People

•Tape

•Carpenter’s Level

•Wood Scrap

•Wedge

•Phillips Head Screw Driver

•Concrete, 540 lb (245 kg) Minimum and Container to Mix

•Wood Board (Scrap)

•Wrenches: (Two) 7/16”, 1/2”, 9/16”, 3/4” or two Large and Small Adjustable Wrenches

•Tape Measure

•Shovel and Spade

•Hammer

•Sawhorse or Support Table

•Step Ladder 8 ft. (2.4 m)

•Safety Goggles

Toll-Free Customer Service Number for U.S: 1-800-558-5234,

For Canada: 1-800-284-8339,

For Europe: 00 800 555 85234 (Sweden: 009 555 85234),

For Australia: 1-800-333 061

Internet Address: http://www.huffysports.com

1

02/04

P/N 21145507

© COPYRIGHT 2000 by HUFFY SPORTS

Image 1

Huffy Sports Basketball Systems manual Inground System Owners Manual, Customer Service Center, 02/04

Contents

Toll-Free Customer Service Number for U.S For Canada Customer Service CenterInground System Owners Manual N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.ABEFORE YOU START these rules for safe operation of the system Owner must ensure that all players know and followDo not slide, climb, shake or play on pole HEIGHT ADJUSTMENT SAFETY INSTRUCTIONSP/N 21145507 02/04 NOTICE TO ASSEMBLERS Remove all contents from boxesPARTS LIST - See Hardware Identifier Item #23 Item #8 Item #27 1 Item #16 Item #12 Item #24 Item #31 HARDWARE IDENTIFIER BOLTS & SCREWSItem #36 HARDWARE IDENTIFIER NUTS & WASHERS2 1/2”, 2 9/16” AND 2 3/4” Wrenches AND/OR SECTION A ASSEMBLE THE POLE2 Socket Wrenches and Sockets 1/2” 9/16” AND a Phillips-Head ScrewdriverBOTTOM MIDDLECONTACT UTILITIES BEFORE DIGGING Tape Not SuppliedFIG. B FIG. C FIG. AFLANGE SIDE VIEWNote A SIDE VIEWNote B Note A7. Install ground sleeve cap 5 onto 10. Attach spacers 10, 11 to pole mount bracket 7 with bolts 12, washers 13, and nuts 14 as shown. IMPORTANT! Tighten until washers 13 no longer move Indicator labels should be applied as close to holes as possible as SIDE ACCESSto prevent labels from being damaged during height adjustment 20 shown in illustrationASSEMBLY WILL VARY DUE TO BACKBOARD STYLE SECTION B ASSEMBLE THE BACKBOARD TO ELEVATOR TUBES2 1/2, 2 9/16” AND 2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets1B. Assemble elevator tubes 30 as shown. Tighten completely 48 molded plastic backboard Fan Use the following assembly instructions if you have a2B. Assemble elevator tubes 30 as shown. Tighten completely 02/04Use the following assembly instructions if you have a a 44” steel-framed acrylic backboardInstructions Included With Backboard Hardware For Board Assembly 3A. Assemble backboard brackets to board as shown Refer ToRefer To AssemblyInstructions Included With RimUse the following assembly instructions if you have a 48” molded plastic-framed acrylic backboardInstall spacers 25, and springs 39 onto backboard BACKBOARD WILL VARY SECTION C ATTACH THE BACKBOARD/ELEVATOR TO POLE SYSTEM2 3/4” Wrenches AND/OR 2 Socket Wrenches and Sockets 3/4”17. Install handle assembly to long WAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEP22 USE EYE PROTECTION WHEN INSTALLING SPRINGSCONCRETE MUST CURE Page Insert net into bottom of clip as shown NET INSTALLATION02/04 IMPORTANT! The elevator holes MUST be parallel with playing surface NOTE A Do not use washers here on spring return style rim NOTE A Do not use washers here on spring return style rimNote A Note A25. A. While holding handle, remove pin B C AB. Move elevator up or down to desired height C. Replace pin 26 full length to lock system at desired height