Appendix a, Place on bottom of hull | Humminbird 937C COMBO guide

www..reelsche93x Man 531370-1mA - vs4atic.qxd 2/18/2005..com11:12 AM Page 89

APPENDIX A

Transducer Mounting Template, Single frequency: XHS-9-20-T

Transducer			bottom	Hulls
Cut and	use for Fiberglass
					Hulls
		use for Aluminum
Cut and

Hull

Place on bottom of hull

fold

Align with transom.

for Installation ") drill type TOP useand ⁵⁄₃₂(4mm & hullfor bit

Fiberglass●Drill

■DrillAluminum

15", 380mm from prop(s).

EITHER ARROWANGLE

Fiberglass

Aluminum 15mm

30mm

Transducer Guide

Remove Transducer Use drill holes two	Level
For use with bracket PN 404329-1

PLACEDEADRISEON

Page 89

Image 89

Humminbird 937C COMBO, 937C DF COMBO manual Appendix a, Place on bottom of hull, Align with transom

Contents

Page Thank YOU Table of Contents Menu System Start-Up Options Menu Contact Humminbird HOW the 900 Series Works Series IntroductionSingle Beam Sonar Dualbeam Plus Sonar Multi-Media Card MMC/SD Slot MULTI-MEDIA Card MMC/SD Slot Installation Overview Accessory BUSAccessory Bus 900 Series has a wide variety of configurations Gimbal Mounting the Control Head Control Head InstallationBasic installation tasks that you must perform include Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Back of Control Head IN-DASH Mounting the Control Head Temperature Plug Cable Connector Assembly to Back of Control Head Connecting the Control Head Power Cable to the Boat Transducer Installation To determine transducer mounting location Transom Transducer InstallationDetermine transducer mounting location Route the transducer cable Moves clockwise as the boat moves Corner of the template Normal Cavitation Confirm that the pivot angle has not changed Attaching the Bracket To attach the pivot to the transducer Dual frequency unit Force is necessary to pivot the assembly Order to gain access to the mounting screws, To route the transom transducer cable all transducers Determine the transducer mounting location Inside the Hull Transducer InstallationTrial installation Route the cable Permanently mount the transducerMake sure the position of the transducer is marked Inside the Hull Test and Finish the Transducer Installation Trolling Motor Transducer Installation If you have… Then use Stem Mounting with AN Existing 1 14 Thread StemHand-tighten only Follow these steps to stem mount the GPS receiver To the cable as shown Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting Location Hand tighten only Speed Accessory InstallationInstall the Speed accessory Rotating Retaining Axial Clip to Remove Paddlewheel Cleaning the Speed accessoryRouting the speed cable to the control head To test the installation Testing the System Installation Series 937c DF Combo Title Screen Getting Started Using Your 900 SeriesPowering UP the Control Head Triplog WHAT’S on the Sonar Display Bottom Presentation Understanding Sonar HistoryReal Time Sonar RTS Window MARK/GOTO key Info key Zoom +/- key POWER/LIGHT KEYKEY Functions Menu KEY View KEYWAY Cursor Control KEY Fishing requirements see View Menu Tab Exit KEY View Preset KeysInfo KEY MARK/GOTO KEY Views and Readouts ViewsSonar views Navigation views Sonar View Sonar ViewSonar Zoom View Split Sonar View Sonar Zoom View Bird’s Eye View BIRD’S EYE View Chart View with Active Cursor Chart/Bird’s Eye Combo View 1112 Chart/Sonar Combo View Chart View with Cursor Present Chart Orientation Navigation Waypoints, Routes and Tracks To save the marked position as a waypoint Navigate to a Waypoint or Position ADD a Waypoint Target or Trolling Grid Chart View with TargetChart View with Grid Save or Clear a Current Track Press Menu Menu System Start-Up Options Menu Sonar Tab, Normal ModeSTART-UP Options Menu Normal Operation Exit Normal operation by powering your 900 Series offSimulator Simulator Self Test Accessory Test Accessory TestSystem Status Self Test Sonar X-PRESS Menu GPS Diagnostic View Split Position Active SideSensitivity To adjust the Lower Range To adjust the Upper RangeUpper Range Lower Range Zoom Level Chart SpeedBottom Lock Sonar Colors Navigation X-Press Menu Highlight Split Position on the Navigation X-Press Menu Save Current Route Save Current TrackClear Current Track Remove Grid Cancel NavigationRemove Target Beam Select Sonar Menu TABTo use Beam Select Highlight Beam Select on the Sonar main menu Fish ID+ To change the Fish ID Sensitivity settingFish ID Sensitivity To turn Fish ID+ on or off Bottom View To adjust the Bottom ViewZoom Width To change the Zoom Width Depth Lines KHZ SensitivitySurface Clutter Noise Filter Transducer Select MAX DepthWater Type Navigation Menu TAB Temperature GraphColor BAR Waypoints TracksRoutes Trolling Grid Rotation North ReferenceTrackpoint Interval Track MIN Distance Delete ALL NAV Data MAP DatumExport ALL NAV Data Chart Detail Level Chart Menu TABTo change the Chart Detail Level setting To change the Map Borders setting Shaded Depth LAT/LON GridSpot Soundings Clear MAP Offset Alarms Menu TABSET MAP Offset Fish ID Alarm Depth AlarmLOW Battery Alarm Temp Alarm Arrival Alarm OFF Course AlarmDrift Alarm To change the Off Course Alarm setting Highlight Alarm Tone on the Alarms main menu Alarm ToneTo change the Alarm Tone setting To change the Units Depth setting Setup Menu TABTo change the Units Temp setting Units Depth Units Distance User ModeUnits Speed Language Restore Defaults Triplog ResetTo Reset Triplog To Restore Defaults To Select Readouts Default Sonar View Customized Sonar View Temp Offset Depth OffsetSpeed Calibration Local Time Zone Position Format Daylight Saving Time Sonar Nmea OutputFollowing Nmea sentences are output To turn Nmea Output on or off Views Menu TAB Accessories Menu TABTo Change the View Status of Any View Highlight the View main menu tab Series Defaults to Simulator with a Transducer Attached TroubleshootingSeries Doesn’t Power Up Problem Possible Cause Display Problems Other electronic devices Finding the Cause of NoiseNoise re-appears Boat’s engine Humminbird Service Policy Year Limited Warranty For IN-WARRANTY service, complete the following steps Returning Your Unit for ServiceSeries Accessories Power Output Specifications Align with transom Appendix aPlace on bottom of hull Appendix B Contact Humminbird

Humminbird 937C COMBO, 937C DF manual Appendix a, Place on bottom of hull, Align with transom

Models: 937C DF COMBO 937C DF 937C COMBO

APPENDIX A

Transducer

bottom

Place on bottom of hull

Align with transom.