Nmea Output, To turn Sonar on or off | Humminbird 937C DF instruction

www..reelsche93x Man 531370-1mA - vs4atic.qxd 2/18/2005..com11:12 AM Page 81

NMEA OUTPUT

(Advanced)

NMEA Output turns the NMEA output on or off. This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.)

The following NMEA sentences are output:

DPT- Depth

MTW - Water Temperature

GLL - Lat/Lon Position

GGA - GPS Fix Data

RMC - Recommended Minimum Specific GNSS Data

VTG - Course Over Ground and Ground Speed

ZDA - Time and Date

When navigating, the following NMEA sentences are also output:

APB - Autopilot Sentence B

BWR - Bearing and Distance to Waypoint

RMB - Recommended Minimum Navigation Info

To turn NMEA Output on or off:

1.Make sure you are in Advanced User Mode, then highlight NMEA Output on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the NMEA Output to On or Off (Off, On, Default = Off).

SONAR

(937c DF Combo and 937c Combo models only)

Sonar deactivates Sonar and removes the Sonar Views from the view rotation.

To turn Sonar on or off:

1.Highlight Sonar on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Sonar to On or Off (Off, On, Default = On).

76

Image 81

Humminbird 937C DF Following Nmea sentences are output, To turn Nmea Output on or off, To turn Sonar on or off

Contents

Page Thank YOU Table of Contents Menu System Start-Up Options Menu Contact Humminbird HOW the 900 Series Works Series IntroductionSingle Beam Sonar Dualbeam Plus Sonar Multi-Media Card MMC/SD Slot MULTI-MEDIA Card MMC/SD Slot Installation Overview Accessory BUSAccessory Bus 900 Series has a wide variety of configurations Control Head Installation Basic installation tasks that you must perform includeGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Back of Control Head IN-DASH Mounting the Control Head Temperature Plug Cable Connector Assembly to Back of Control Head Connecting the Control Head Power Cable to the Boat Transducer Installation To determine transducer mounting location Transom Transducer InstallationDetermine transducer mounting location Route the transducer cable Moves clockwise as the boat moves Corner of the template Normal Cavitation Confirm that the pivot angle has not changed Attaching the Bracket To attach the pivot to the transducer Dual frequency unit Force is necessary to pivot the assembly Order to gain access to the mounting screws, To route the transom transducer cable all transducers Inside the Hull Transducer Installation Trial installationDetermine the transducer mounting location Route the cable Permanently mount the transducerMake sure the position of the transducer is marked Inside the Hull Test and Finish the Transducer Installation Trolling Motor Transducer Installation If you have… Then use Stem Mounting with AN Existing 1 14 Thread StemHand-tighten only Follow these steps to stem mount the GPS receiver To the cable as shown Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting Location Speed Accessory Installation Install the Speed accessoryHand tighten only Cleaning the Speed accessory Routing the speed cable to the control headRotating Retaining Axial Clip to Remove Paddlewheel To test the installation Testing the System Installation Getting Started Using Your 900 Series Powering UP the Control HeadSeries 937c DF Combo Title Screen Triplog WHAT’S on the Sonar Display Understanding Sonar History Real Time Sonar RTS WindowBottom Presentation POWER/LIGHT KEY KEY FunctionsMARK/GOTO key Info key Zoom +/- key Menu KEY View KEYWAY Cursor Control KEY Fishing requirements see View Menu Tab Exit KEY View Preset KeysInfo KEY MARK/GOTO KEY Views and Readouts ViewsSonar views Navigation views Sonar View Sonar Zoom ViewSonar View Split Sonar View Sonar Zoom View Bird’s Eye View BIRD’S EYE View Chart View with Active Cursor Chart/Bird’s Eye Combo View 1112 Chart/Sonar Combo View Chart View with Cursor Present Chart Orientation Navigation Waypoints, Routes and Tracks To save the marked position as a waypoint Navigate to a Waypoint or Position Chart View with Target Chart View with GridADD a Waypoint Target or Trolling Grid Save or Clear a Current Track Press Menu Menu System Sonar Tab, Normal Mode START-UP Options MenuStart-Up Options Menu Normal Operation Exit Normal operation by powering your 900 Series offSimulator Simulator Self Test Accessory Test Accessory TestSystem Status Self Test Sonar X-PRESS Menu GPS Diagnostic View Active Side SensitivitySplit Position To adjust the Lower Range To adjust the Upper RangeUpper Range Lower Range Zoom Level Chart SpeedBottom Lock Sonar Colors Navigation X-Press Menu Highlight Split Position on the Navigation X-Press Menu Save Current Track Clear Current TrackSave Current Route Cancel Navigation Remove TargetRemove Grid Beam Select Sonar Menu TABTo use Beam Select Highlight Beam Select on the Sonar main menu Fish ID+ To change the Fish ID Sensitivity settingFish ID Sensitivity To turn Fish ID+ on or off Bottom View To adjust the Bottom ViewZoom Width To change the Zoom Width Depth Lines KHZ SensitivitySurface Clutter Noise Filter MAX Depth Water TypeTransducer Select Temperature Graph Color BARNavigation Menu TAB Tracks RoutesWaypoints Trolling Grid Rotation North ReferenceTrackpoint Interval Track MIN Distance MAP Datum Export ALL NAV DataDelete ALL NAV Data Chart Detail Level Chart Menu TABTo change the Chart Detail Level setting To change the Map Borders setting LAT/LON Grid Spot SoundingsShaded Depth Alarms Menu TAB SET MAP OffsetClear MAP Offset Fish ID Alarm Depth AlarmLOW Battery Alarm Temp Alarm Arrival Alarm OFF Course AlarmDrift Alarm To change the Off Course Alarm setting Alarm Tone To change the Alarm Tone settingHighlight Alarm Tone on the Alarms main menu To change the Units Depth setting Setup Menu TABTo change the Units Temp setting Units Depth Units Distance User ModeUnits Speed Language Restore Defaults Triplog ResetTo Reset Triplog To Restore Defaults To Select Readouts Default Sonar View Customized Sonar View Temp Offset Depth OffsetSpeed Calibration Local Time Zone Position Format Daylight Saving Time Sonar Nmea OutputFollowing Nmea sentences are output To turn Nmea Output on or off Views Menu TAB Accessories Menu TABTo Change the View Status of Any View Highlight the View main menu tab Troubleshooting Series Doesn’t Power UpSeries Defaults to Simulator with a Transducer Attached Problem Possible Cause Display Problems Other electronic devices Finding the Cause of NoiseNoise re-appears Boat’s engine Humminbird Service Policy Year Limited Warranty Returning Your Unit for Service Series AccessoriesFor IN-WARRANTY service, complete the following steps Power Output Specifications Appendix a Place on bottom of hullAlign with transom Appendix B Contact Humminbird