Humminbird 937C DF COMBO, 937C COMBO instruction

www..reelsche93x Man 531370-1mA - vs4atic.qxd 2/18/2005..com11:11 AM Page 1

Image 1

Humminbird 937C DF COMBO, 937C COMBO manual

Contents

Page Thank YOU Table of Contents Menu System Start-Up Options Menu Contact Humminbird HOW the 900 Series Works Series IntroductionSingle Beam Sonar Dualbeam Plus Sonar Multi-Media Card MMC/SD Slot MULTI-MEDIA Card MMC/SD Slot Installation Overview Accessory BUSAccessory Bus 900 Series has a wide variety of configurations Basic installation tasks that you must perform include Control Head InstallationGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Back of Control Head IN-DASH Mounting the Control Head Temperature Plug Cable Connector Assembly to Back of Control Head Connecting the Control Head Power Cable to the Boat Transducer Installation To determine transducer mounting location Transom Transducer InstallationDetermine transducer mounting location Route the transducer cable Moves clockwise as the boat moves Corner of the template Normal Cavitation Confirm that the pivot angle has not changed Attaching the Bracket To attach the pivot to the transducer Dual frequency unit Force is necessary to pivot the assembly Order to gain access to the mounting screws, To route the transom transducer cable all transducers Trial installation Inside the Hull Transducer InstallationDetermine the transducer mounting location Route the cable Permanently mount the transducerMake sure the position of the transducer is marked Inside the Hull Test and Finish the Transducer Installation Trolling Motor Transducer Installation If you have… Then use Stem Mounting with AN Existing 1 14 Thread StemHand-tighten only Follow these steps to stem mount the GPS receiver To the cable as shown Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting Location Install the Speed accessory Speed Accessory InstallationHand tighten only Routing the speed cable to the control head Cleaning the Speed accessoryRotating Retaining Axial Clip to Remove Paddlewheel To test the installation Testing the System Installation Powering UP the Control Head Getting Started Using Your 900 SeriesSeries 937c DF Combo Title Screen Triplog WHAT’S on the Sonar Display Real Time Sonar RTS Window Understanding Sonar HistoryBottom Presentation KEY Functions POWER/LIGHT KEYMARK/GOTO key Info key Zoom +/- key Menu KEY View KEYWAY Cursor Control KEY Fishing requirements see View Menu Tab Exit KEY View Preset KeysInfo KEY MARK/GOTO KEY Views and Readouts ViewsSonar views Navigation views Sonar Zoom View Sonar ViewSonar View Split Sonar View Sonar Zoom View Bird’s Eye View BIRD’S EYE View Chart View with Active Cursor Chart/Bird’s Eye Combo View 1112 Chart/Sonar Combo View Chart View with Cursor Present Chart Orientation Navigation Waypoints, Routes and Tracks To save the marked position as a waypoint Navigate to a Waypoint or Position Chart View with Grid Chart View with TargetADD a Waypoint Target or Trolling Grid Save or Clear a Current Track Press Menu Menu System START-UP Options Menu Sonar Tab, Normal ModeStart-Up Options Menu Normal Operation Exit Normal operation by powering your 900 Series offSimulator Simulator Self Test Accessory Test Accessory TestSystem Status Self Test Sonar X-PRESS Menu GPS Diagnostic View Sensitivity Active SideSplit Position To adjust the Lower Range To adjust the Upper RangeUpper Range Lower Range Zoom Level Chart SpeedBottom Lock Sonar Colors Navigation X-Press Menu Highlight Split Position on the Navigation X-Press Menu Clear Current Track Save Current TrackSave Current Route Remove Target Cancel NavigationRemove Grid Beam Select Sonar Menu TABTo use Beam Select Highlight Beam Select on the Sonar main menu Fish ID+ To change the Fish ID Sensitivity settingFish ID Sensitivity To turn Fish ID+ on or off Bottom View To adjust the Bottom ViewZoom Width To change the Zoom Width Depth Lines KHZ SensitivitySurface Clutter Noise Filter Water Type MAX DepthTransducer Select Color BAR Temperature GraphNavigation Menu TAB Routes TracksWaypoints Trolling Grid Rotation North ReferenceTrackpoint Interval Track MIN Distance Export ALL NAV Data MAP DatumDelete ALL NAV Data Chart Detail Level Chart Menu TABTo change the Chart Detail Level setting To change the Map Borders setting Spot Soundings LAT/LON GridShaded Depth SET MAP Offset Alarms Menu TABClear MAP Offset Fish ID Alarm Depth AlarmLOW Battery Alarm Temp Alarm Arrival Alarm OFF Course AlarmDrift Alarm To change the Off Course Alarm setting To change the Alarm Tone setting Alarm ToneHighlight Alarm Tone on the Alarms main menu To change the Units Depth setting Setup Menu TABTo change the Units Temp setting Units Depth Units Distance User ModeUnits Speed Language Restore Defaults Triplog ResetTo Reset Triplog To Restore Defaults To Select Readouts Default Sonar View Customized Sonar View Temp Offset Depth OffsetSpeed Calibration Local Time Zone Position Format Daylight Saving Time Sonar Nmea OutputFollowing Nmea sentences are output To turn Nmea Output on or off Views Menu TAB Accessories Menu TABTo Change the View Status of Any View Highlight the View main menu tab Series Doesn’t Power Up TroubleshootingSeries Defaults to Simulator with a Transducer Attached Problem Possible Cause Display Problems Other electronic devices Finding the Cause of NoiseNoise re-appears Boat’s engine Humminbird Service Policy Year Limited Warranty Series Accessories Returning Your Unit for ServiceFor IN-WARRANTY service, complete the following steps Power Output Specifications Place on bottom of hull Appendix aAlign with transom Appendix B Contact Humminbird