Normal Operation, Simulator | Humminbird 937C DF COMBO instruction

www..reelsche93x Man 531370-1mA - vs4atic.qxd 2/18/2005..com11:12 AM Page 51

NORMAL OPERATION

Use Normal operation for on-the-water operation with a transducer connected. In addition, your 900 Series™ uses advanced transducer detection methods to determine if a transducer is connected. If a functioning transducer is connected, Normal operation will be selected automatically at power up and your 900 Series™ can be used on the water.

Exit Normal operation by powering your 900 Series™ off.

SIMULATOR

Use the Simulator to learn how to use your 900 Series™ before taking your boat on the water. The Simulator is a very powerful tool that simulates on-the-water operation, providing a randomly-updated display. We recommend going through this manual while using the Simulator, since all of the menus function and affect the display the way they actually do when in Normal operation.

Simulator

NOTE: To get the full benefit of the Simulator, it is important to select Simulator manually from the Start-Up Options menu as opposed to letting the 900 Series™ enter Simulator automatically (as it will if a transducer is not connected and you do nothing during power up). Manually selecting Simulator from the Start-Up Options menu allows you to pre- configure your 900 Series™ for on-the-water operation. Any menu changes you make will be saved for later use.

A Simulation message will appear on the display periodically to remind you that you are using the Simulator.

Exit the Simulator by powering your 900 Series™ off.

46

Image 51

Humminbird 937C DF COMBO, 937C COMBO Normal Operation, Simulator, Exit Normal operation by powering your 900 Series off

Contents

Page Thank YOU Table of Contents Menu System Start-Up Options Menu Contact Humminbird Dualbeam Plus Sonar Series IntroductionHOW the 900 Series Works Single Beam Sonar Multi-Media Card MMC/SD Slot MULTI-MEDIA Card MMC/SD Slot 900 Series has a wide variety of configurations Accessory BUSInstallation Overview Accessory Bus Control Head Installation Basic installation tasks that you must perform includeGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Back of Control Head IN-DASH Mounting the Control Head Temperature Plug Cable Connector Assembly to Back of Control Head Connecting the Control Head Power Cable to the Boat Transducer Installation Route the transducer cable Transom Transducer InstallationTo determine transducer mounting location Determine transducer mounting location Moves clockwise as the boat moves Corner of the template Normal Cavitation Confirm that the pivot angle has not changed Attaching the Bracket To attach the pivot to the transducer Dual frequency unit Force is necessary to pivot the assembly Order to gain access to the mounting screws, To route the transom transducer cable all transducers Inside the Hull Transducer Installation Trial installationDetermine the transducer mounting location Inside the Hull Permanently mount the transducerRoute the cable Make sure the position of the transducer is marked Test and Finish the Transducer Installation Trolling Motor Transducer Installation Follow these steps to stem mount the GPS receiver Stem Mounting with AN Existing 1 14 Thread StemIf you have… Then use Hand-tighten only To the cable as shown Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting Location Speed Accessory Installation Install the Speed accessoryHand tighten only Cleaning the Speed accessory Routing the speed cable to the control headRotating Retaining Axial Clip to Remove Paddlewheel To test the installation Testing the System Installation Getting Started Using Your 900 Series Powering UP the Control HeadSeries 937c DF Combo Title Screen Triplog WHAT’S on the Sonar Display Understanding Sonar History Real Time Sonar RTS WindowBottom Presentation POWER/LIGHT KEY KEY FunctionsMARK/GOTO key Info key Zoom +/- key Fishing requirements see View Menu Tab View KEYMenu KEY WAY Cursor Control KEY MARK/GOTO KEY View Preset KeysExit KEY Info KEY Navigation views ViewsViews and Readouts Sonar views Sonar View Sonar Zoom ViewSonar View Split Sonar View Sonar Zoom View Bird’s Eye View BIRD’S EYE View Chart View with Active Cursor Chart/Bird’s Eye Combo View 1112 Chart/Sonar Combo View Chart View with Cursor Present Chart Orientation Navigation Waypoints, Routes and Tracks To save the marked position as a waypoint Navigate to a Waypoint or Position Chart View with Target Chart View with GridADD a Waypoint Target or Trolling Grid Save or Clear a Current Track Press Menu Menu System Sonar Tab, Normal Mode START-UP Options MenuStart-Up Options Menu Simulator Exit Normal operation by powering your 900 Series offNormal Operation Simulator Self Test Accessory TestSelf Test Accessory Test System Status Sonar X-PRESS Menu GPS Diagnostic View Active Side SensitivitySplit Position Lower Range To adjust the Upper RangeTo adjust the Lower Range Upper Range Sonar Colors Chart SpeedZoom Level Bottom Lock Navigation X-Press Menu Highlight Split Position on the Navigation X-Press Menu Save Current Track Clear Current TrackSave Current Route Cancel Navigation Remove TargetRemove Grid Highlight Beam Select on the Sonar main menu Sonar Menu TABBeam Select To use Beam Select To turn Fish ID+ on or off To change the Fish ID Sensitivity settingFish ID+ Fish ID Sensitivity To change the Zoom Width To adjust the Bottom ViewBottom View Zoom Width Noise Filter KHZ SensitivityDepth Lines Surface Clutter MAX Depth Water TypeTransducer Select Temperature Graph Color BARNavigation Menu TAB Tracks RoutesWaypoints Track MIN Distance North ReferenceTrolling Grid Rotation Trackpoint Interval MAP Datum Export ALL NAV DataDelete ALL NAV Data To change the Map Borders setting Chart Menu TABChart Detail Level To change the Chart Detail Level setting LAT/LON Grid Spot SoundingsShaded Depth Alarms Menu TAB SET MAP OffsetClear MAP Offset Temp Alarm Depth AlarmFish ID Alarm LOW Battery Alarm To change the Off Course Alarm setting OFF Course AlarmArrival Alarm Drift Alarm Alarm Tone To change the Alarm Tone settingHighlight Alarm Tone on the Alarms main menu Units Depth Setup Menu TABTo change the Units Depth setting To change the Units Temp setting Language User ModeUnits Distance Units Speed To Restore Defaults Triplog ResetRestore Defaults To Reset Triplog To Select Readouts Default Sonar View Customized Sonar View Local Time Zone Depth OffsetTemp Offset Speed Calibration Position Format Daylight Saving Time To turn Nmea Output on or off Nmea OutputSonar Following Nmea sentences are output Highlight the View main menu tab Accessories Menu TABViews Menu TAB To Change the View Status of Any View Troubleshooting Series Doesn’t Power UpSeries Defaults to Simulator with a Transducer Attached Problem Possible Cause Display Problems Boat’s engine Finding the Cause of NoiseOther electronic devices Noise re-appears Humminbird Service Policy Year Limited Warranty Returning Your Unit for Service Series AccessoriesFor IN-WARRANTY service, complete the following steps Power Output Specifications Appendix a Place on bottom of hullAlign with transom Appendix B Contact Humminbird