Appendix B | Humminbird 937C DF COMBO, 937C COMBO manual

www..reelsche93x Man 531370-1mA - vs4atic.qxd 2/18/2005..com11:12 AM Page 90

APPENDIX B

Transducer Mounting Template, Dual frequency: XHS-9-DB-74-T

85

Image 90

Humminbird 937C DF COMBO, 937C COMBO manual Appendix B

Contents

Page Thank YOU Table of Contents Menu System Start-Up Options Menu Contact Humminbird Single Beam Sonar Series IntroductionHOW the 900 Series Works Dualbeam Plus Sonar MULTI-MEDIA Card MMC/SD Slot Multi-Media Card MMC/SD Slot Accessory Bus Accessory BUSInstallation Overview 900 Series has a wide variety of configurations Control Head Installation Basic installation tasks that you must perform includeGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Back of Control Head IN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head Temperature Transducer Installation Connecting the Control Head Power Cable to the Boat Determine transducer mounting location Transom Transducer InstallationTo determine transducer mounting location Route the transducer cable Corner of the template Moves clockwise as the boat moves Confirm that the pivot angle has not changed Normal Cavitation To attach the pivot to the transducer Dual frequency unit Attaching the Bracket Order to gain access to the mounting screws, Force is necessary to pivot the assembly To route the transom transducer cable all transducers Inside the Hull Transducer Installation Trial installationDetermine the transducer mounting location Make sure the position of the transducer is marked Permanently mount the transducerRoute the cable Inside the Hull Trolling Motor Transducer Installation Test and Finish the Transducer Installation Hand-tighten only Stem Mounting with AN Existing 1 14 Thread StemIf you have… Then use Follow these steps to stem mount the GPS receiver Access Under Mounting Location To the cable as shown No Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver Operation Speed Accessory Installation Install the Speed accessoryHand tighten only Cleaning the Speed accessory Routing the speed cable to the control headRotating Retaining Axial Clip to Remove Paddlewheel Testing the System Installation To test the installation Getting Started Using Your 900 Series Powering UP the Control HeadSeries 937c DF Combo Title Screen WHAT’S on the Sonar Display Triplog Understanding Sonar History Real Time Sonar RTS WindowBottom Presentation POWER/LIGHT KEY KEY FunctionsMARK/GOTO key Info key Zoom +/- key WAY Cursor Control KEY View KEYMenu KEY Fishing requirements see View Menu Tab Info KEY View Preset KeysExit KEY MARK/GOTO KEY Sonar views ViewsViews and Readouts Navigation views Sonar View Sonar Zoom ViewSonar View Sonar Zoom View Split Sonar View BIRD’S EYE View Bird’s Eye View Chart/Bird’s Eye Combo View Chart View with Active Cursor Chart/Sonar Combo View 1112 Chart Orientation Chart View with Cursor Present Navigation To save the marked position as a waypoint Waypoints, Routes and Tracks Navigate to a Waypoint or Position Chart View with Target Chart View with GridADD a Waypoint Target or Trolling Grid Save or Clear a Current Track Menu System Press Menu Sonar Tab, Normal Mode START-UP Options MenuStart-Up Options Menu Simulator Exit Normal operation by powering your 900 Series offNormal Operation Simulator System Status Accessory TestSelf Test Accessory Test Self Test GPS Diagnostic View Sonar X-PRESS Menu Active Side SensitivitySplit Position Upper Range To adjust the Upper RangeTo adjust the Lower Range Lower Range Bottom Lock Chart SpeedZoom Level Sonar Colors Highlight Split Position on the Navigation X-Press Menu Navigation X-Press Menu Save Current Track Clear Current TrackSave Current Route Cancel Navigation Remove TargetRemove Grid To use Beam Select Sonar Menu TABBeam Select Highlight Beam Select on the Sonar main menu Fish ID Sensitivity To change the Fish ID Sensitivity settingFish ID+ To turn Fish ID+ on or off Zoom Width To adjust the Bottom ViewBottom View To change the Zoom Width Surface Clutter KHZ SensitivityDepth Lines Noise Filter MAX Depth Water TypeTransducer Select Temperature Graph Color BARNavigation Menu TAB Tracks RoutesWaypoints Trackpoint Interval North ReferenceTrolling Grid Rotation Track MIN Distance MAP Datum Export ALL NAV DataDelete ALL NAV Data To change the Chart Detail Level setting Chart Menu TABChart Detail Level To change the Map Borders setting LAT/LON Grid Spot SoundingsShaded Depth Alarms Menu TAB SET MAP OffsetClear MAP Offset LOW Battery Alarm Depth AlarmFish ID Alarm Temp Alarm Drift Alarm OFF Course AlarmArrival Alarm To change the Off Course Alarm setting Alarm Tone To change the Alarm Tone settingHighlight Alarm Tone on the Alarms main menu To change the Units Temp setting Setup Menu TABTo change the Units Depth setting Units Depth Units Speed User ModeUnits Distance Language To Reset Triplog Triplog ResetRestore Defaults To Restore Defaults Default Sonar View Customized Sonar View To Select Readouts Speed Calibration Depth OffsetTemp Offset Local Time Zone Daylight Saving Time Position Format Following Nmea sentences are output Nmea OutputSonar To turn Nmea Output on or off To Change the View Status of Any View Accessories Menu TABViews Menu TAB Highlight the View main menu tab Troubleshooting Series Doesn’t Power UpSeries Defaults to Simulator with a Transducer Attached Display Problems Problem Possible Cause Noise re-appears Finding the Cause of NoiseOther electronic devices Boat’s engine Year Limited Warranty Humminbird Service Policy Returning Your Unit for Service Series AccessoriesFor IN-WARRANTY service, complete the following steps Specifications Power Output Appendix a Place on bottom of hullAlign with transom Appendix B Contact Humminbird