Panasonic WJ-HD616K, WJ-HD716K manual Specifications, • General, • Input/output

Specifications

• General

Power source:	120 V AC, 60 Hz
Power consumption:	130 W
Ambient operating temperature:	+5 °C to +45 °C {+41 °F to +113 °F}
Ambient operating humidity:	5 % to 90 % (non condensing)
	When installing WJ-HDB611: 10 % to 80 % (non condensing)
Maximum operating altitude:	2 000 m {6 562 feet} or less
Dimensions (excluding rubber
feet and projections)	430 mm (W) x 132 mm (H) x 400 mm (D) {16-15/16"" (W) x 5-3/16" (H) x 15-3/4" (D)}
Weight:	When no hard disk drive is installed: 14 kg {30.91 lbs.}
	When 4 hard disk drives are installed: 17 kg {37.53 lbs.}
Finish:	Front cover: Solid metallic coating
	Top cover: Solid metallic coating
	Rear panel: Galvanized steel

• HDD (Locally procured - Contact your dealer about purchasing hard disk drives.)

Hard disk drive:3.5" hard disk drive (Up to 4 hard disk drives can be installed.)

• Input/output

Video
Video input connector:	1 V [p-p]/75 Ω, x16 (1ch to 16ch) (BNC)
	Vertical timing pulse multiplexed, HD616K: x8 (1ch to 8ch), HD716K: x16
Cascade input connector:	1 V [p-p]/75 Ω (BNC)
	HDMI, x2
Video output connector:	1 V [p-p]/75 Ω, active loop-thru output, x16 (1ch to 16ch) (BNC)*1
Monitor output connector:	1 V [p-p]/75 Ω, x2 (BNC)
Monitor (HDMI) connector:	HDMI, x2*8
Video output connector (front):	1 V [p-p]/75 Ω, x1 (RCA pin)
Audio
Audio input connector:	–10 dBv, 10 kΩ, unbalanced, x4 (RCA pin)
Cascade input connector:	–10 dBv, 10 kΩ, unbalanced x 1 (RCA pin)
Audio output connector:	–10 dBv, 600 Ω, unbalanced, x1 (RCA pin)
Audio output connector (front):	–10 dBv, 600 Ω, unbalanced, x1 (RCA pin)
Others
External storage connector:	x3
Mouse connection port:	x1
Alarm/control terminal:	8 to 16ch alarm output*3, alarm reset input*2, emergency recording input*2, available
	space warning output*3, HDD trouble output*3, camera trouble output*3, trouble out-
	put*3, electricity failure recovery completion output*4, time adjust input/output*5,
	sequence switching input/output*5, alarm suspension input*2, electricity failure detec-
	tion input*2, external recording mode switching*2, +5 V output*6 (25-pin D-sub)
Alarm terminal:	1ch - 16ch alarm input*2, 1 - 7ch alarm output*3 (25-pin D-sub)
RS485 port:	RS485 (full duplex/half duplex*7), x2 (RJ-11)
DATA port:	RS485, x2 (RJ-11)
Network port:	10BASE-T/100BASE-TX (RJ-45)
Maintenance port:	10BASE-T (RJ-45)
SDHC/SD memory card slot:	SDHC/SD memory cards applicable (miniSD cards and microSD cards not applica-
	ble)

*1 When power is not supplied, the video output signal was not sent from the recorder even if a video input signal is supplied. *2 Non-voltage make contact input, 50 kΩ +5 V DC pull-up

153