UT-112/UT-98 installation | Icom IC-M504 specs

9 CONNECTIONS AND MAINTENANCE

■UT-112/UT-98 installation

CAUTION: DISCONNECT the DC power cable from the transceiver before performing any work on the transceiver. Otherwise, there is danger of electric shock and/or equip- ment damage.

Follow the case opening procedure shown here when you want to install an optional scrambler unit.

qRemove the 6 screws as shown below and open the trans- ceiver.

wDisconnect the ﬂat cable and NMEA (4 pin) from J5 of the LOGIC unit.

LOGIC unit

NMEA (4 pin)

q

Flat cable

w

eInstall an optional unit (UT-112 or UT-98) to J3 on the AF unit as shown below.

Optional unit

J3

AF unit

62

Image 68

Icom IC-M504 instruction manual UT-112/UT-98 installation

Contents

IM504 Word Definition May occurEquipment damage may occur Personal injury, ﬁre or electric shock Case of Emergency Determining MPE Radius Iii Table of Contents Precautions Operating Rules Radio license for boaters U.S.A. onlyShip Station License OPERATOR’S License Panel Description Front panel 2TRANSMIT Power KEY H/L 0TIME Zone Indicator Function display Microphone 1POSITION Indicator2SCAN Indicator Basic Operation Channel selectionChannel Channel 9 Call channel S.A., international and Canadian channels Weather channelsC to change the channel group, if necessary Rotate Dial to select a channel Receiving and transmitting Push CH/WXDUAL Call channel programmingWhile pushing and holding Channel comments Microphone Lock functionDisplay backlight Select the desired charac Dialenter Optional voice scrambler operationActivating the scrambler Programming scrambler codes Scan Operation Scan typesPriority Scan Normal Scan Starting a scan Setting TAG channelsClearing or setting all tagged channels DUALWATCH/TRI-WATCH DescriptionOperation DUALWATCH/TRI-WATCH Simulation DSC Operation Mmsi code programmingRotate Dial to select Mmsi Check, push Dialenter Rotate Dial to set the speciﬁc 9-digit Mmsi code Mmsi code check Check the 9-digit Mmsi DSC self ID code DSC address ID Programming Individual IDRotate Dial to select AddINDV ID, push Dialenter Rotate Dial to set the individual ID and ID name Rotate Dial to select the desired ID name for deleting Deleting Individual IDRotate Dial to select Delindv ID, push Dialenter Rotate Dial to set the group ID and ID name Programming Group IDRotate Dial to select AddGroup ID, push Dialenter Deleting Group ID Rotate Dial to select DELGroup ID, push Dialenter Position and time programming Position and time indication GPS information indication After 2 sec. Wait ACK Distress callSimple call Distress alert contains default Regular call Push Distress for 5 sec. to transmit the distress call Transmitting DSC calls Transmitting an individual call Push Dialenter to transmit the individual call Transmitting an individual acknowledgement Transmitting a group call Push Dialenter to transmit the group call Push Dialenter to transmit the all ships call Transmitting an all ships callRotate Dial to select the desired category, push Dialenter Transmitting a position request call Push Dialenter to transmit the position request call Transmitting a position report call Push Dialenter to transmit the position report call Transmitting a polling request call Push Dialenter to transmit the polling request call Transmitting a position request reply call Your position data is transmitted, when Dialenter is pushed Transmitting a position report reply call Transmitting a polling request reply call Receiving DSC calls Receiving a distress callReceiving a distress acknowledgement Receiving a distress relay call Receiving an all ships call Receiving an individual callReceiving a group call Receiving a position report call Receiving a geographical area callReceiving a position request call Receiving a polling request call Receiving a position request reply callReceiving a position report reply call Receiving a polling request reply call Received messages Distress messageRotate Dial to select Distress, push Dialenter Rotate Dial to scroll the message Other messages Rotate Dial to select Other, push Dialenter Rotate Dial to select Offset Time, push Dialenter DSC Set modeNo offset time default Push Dialenter to set the condition Automatic acknowledgementRotate Dial to select Auto ACK, push Nmea Output Rotate Dial to select Nmea Output, push Dialenter HM-162 listener Other FunctionsIntercom operation RX Speaker function To return to normal operation, push CLR or Hailrx Push Hailrx to enter hailer modeHailer operation Automatic foghorn function UnderwayStop Sail Ing DSC calls.’ p Rotate Dial to adjust the foghorn level, push DialenterTion is interrupted with an automatic return to the trans SET Mode Set mode programmingSet mode items Scan resume timer Weather alert Dual/Tri-watchBeep tone LCD contrast Radio power Automatic foghorn frequencyScrambler type Scrambler code Connections Connections and Maintenance0DC Power Connector Antenna Fuse replacementSupplied accessories Using the supplied mounting bracket Mounting the transceiver That the clamps press firmly against the inside MB-75 installationTighten the end bolts on the clamps rotate clockwise so UT-112/UT-98 installation HM-162/HM-157 installation Return the cables and screws to the original position Completed installation should look like this HM-162HM-157 HM-162 HM-157 Gasket Mm 131⁄32˝ Nut Cap Troubleshooting Problem Possible Cause Solution Specifications and Options SpeciﬁcationsGeneral Receiver Transmitter Dimensions OptionsFor mounting the transceiver to a panel 20 feet microphone extension cable for optional HM Channel List Transmit Receive Unit mm inch Cut here TemplateR12 Max Page Memo Kamiminami, Hirano-ku, Osaka 547-0003, Japan