HM-162 HM-157 | Icom IC-M504 manual

9 CONNECTIONS AND MAINTENANCE

qInsert the supplied cable into the external microphone jack and tighten the cable nut as shown below.

wTo use the supplied cable as a wall socket, perform the fol- lowing steps.

eUsing the mounting base as a template, carefully mark the holes where the cable and three screws will be fastened.

rDrill holes at these marks.

tInstall the mounting base using the supplied screws as shown below.

• HM-162

Mounting base

Nut

Gasket
Screw holes
(approx. 2 (d) mm; 3 32″ )	Cap

•HM-157

Mounting base

Nut

Gasket
Screw holes
(approx. 2 (d) mm; 3 32″ )	Cap

yThe completed installation should look like this.

• HM-162			• HM-157

64

Image 70

Icom IC-M504 instruction manual Completed installation should look like this, HM-162 HM-157

Contents

IM504 Equipment damage may occur Word DefinitionMay occur Personal injury, ﬁre or electric shock Case of Emergency Determining MPE Radius Iii Table of Contents Precautions Ship Station License Operating RulesRadio license for boaters U.S.A. only OPERATOR’S License Panel Description Front panel 2TRANSMIT Power KEY H/L 0TIME Zone Indicator Function display 2SCAN Indicator 1POSITION IndicatorMicrophone Channel Basic OperationChannel selection Channel 9 Call channel C to change the channel group, if necessary S.A., international and Canadian channelsWeather channels Rotate Dial to select a channel Receiving and transmitting While pushing and holding Call channel programmingPush CH/WXDUAL Display backlight Channel commentsMicrophone Lock function Select the desired charac Activating the scrambler Programming scrambler codes Optional voice scrambler operationDialenter Priority Scan Scan OperationScan types Normal Scan Clearing or setting all tagged channels Setting TAG channelsStarting a scan Operation DUALWATCH/TRI-WATCHDescription DUALWATCH/TRI-WATCH Simulation Rotate Dial to select Mmsi Check, push Dialenter DSC OperationMmsi code programming Rotate Dial to set the speciﬁc 9-digit Mmsi code Mmsi code check Check the 9-digit Mmsi DSC self ID code Rotate Dial to select AddINDV ID, push Dialenter DSC address IDProgramming Individual ID Rotate Dial to set the individual ID and ID name Rotate Dial to select Delindv ID, push Dialenter Deleting Individual IDRotate Dial to select the desired ID name for deleting Rotate Dial to select AddGroup ID, push Dialenter Programming Group IDRotate Dial to set the group ID and ID name Deleting Group ID Rotate Dial to select DELGroup ID, push Dialenter Position and time programming Position and time indication GPS information indication Simple call Distress callAfter 2 sec. Wait ACK Distress alert contains default Regular call Push Distress for 5 sec. to transmit the distress call Transmitting DSC calls Transmitting an individual call Push Dialenter to transmit the individual call Transmitting an individual acknowledgement Transmitting a group call Push Dialenter to transmit the group call Rotate Dial to select the desired category, push Dialenter Transmitting an all ships callPush Dialenter to transmit the all ships call Transmitting a position request call Push Dialenter to transmit the position request call Transmitting a position report call Push Dialenter to transmit the position report call Transmitting a polling request call Push Dialenter to transmit the polling request call Transmitting a position request reply call Your position data is transmitted, when Dialenter is pushed Transmitting a position report reply call Transmitting a polling request reply call Receiving a distress acknowledgement Receiving DSC callsReceiving a distress call Receiving a distress relay call Receiving a group call Receiving an individual callReceiving an all ships call Receiving a position request call Receiving a geographical area callReceiving a position report call Receiving a position report reply call Receiving a polling request callReceiving a position request reply call Receiving a polling request reply call Rotate Dial to select Distress, push Dialenter Received messagesDistress message Rotate Dial to scroll the message Other messages Rotate Dial to select Other, push Dialenter No offset time default DSC Set modeRotate Dial to select Offset Time, push Dialenter Rotate Dial to select Auto ACK, push Automatic acknowledgementPush Dialenter to set the condition Nmea Output Rotate Dial to select Nmea Output, push Dialenter Intercom operation Other FunctionsHM-162 listener RX Speaker function Hailer operation Push Hailrx to enter hailer modeTo return to normal operation, push CLR or Hailrx Stop Automatic foghorn functionUnderway Sail Tion is interrupted with an automatic return to the trans Rotate Dial to adjust the foghorn level, push DialenterIng DSC calls.’ p Set mode items SET ModeSet mode programming Scan resume timer Beep tone Weather alertDual/Tri-watch LCD contrast Scrambler type Radio powerAutomatic foghorn frequency Scrambler code 0DC Power Connector Connections and MaintenanceConnections Supplied accessories Fuse replacementAntenna Using the supplied mounting bracket Mounting the transceiver Tighten the end bolts on the clamps rotate clockwise so MB-75 installationThat the clamps press firmly against the inside UT-112/UT-98 installation HM-162/HM-157 installation Return the cables and screws to the original position HM-157 Completed installation should look like thisHM-162 HM-162 HM-157 Gasket Mm 131⁄32˝ Nut Cap Troubleshooting Problem Possible Cause Solution General Receiver Specifications and OptionsSpeciﬁcations Transmitter For mounting the transceiver to a panel DimensionsOptions 20 feet microphone extension cable for optional HM Channel List Transmit Receive R12 Max TemplateUnit mm inch Cut here Page Memo Kamiminami, Hirano-ku, Osaka 547-0003, Japan