13 TROUBLESHOOTING
The following chart is designed to help you correct problems which are not equipment malfunctions. If you are unable to locate the cause of a problem or
solve it through the use of this chart, contact your nearest Icom Dealer or Service Center.
POWER
RECEIVE FUNCTIONS
FRONT PANEL CONTROL
PROBLEM | POSSIBLE CAUSE | SOLUTION | REF. | |
Power does not turn | • DC power cable is improperly con- | • Reconnect the DC power cable se- | p. 8 | |
ON when [POWER] is | nected. | curely. |
|
|
pushed in. | • A fuse is blown. | • Check for the cause, then replace the | p. 37 | |
|
| fuse with a spare one. |
| |
| • During AC adapter operation, the | • Connect the jumper connector to the | p. 8 | |
| jumper connector is not in use. | [DC13.8V] jack on the receiver’s rear panel. |
| |
| • External 12 V DC is connected to the | • Connect the external power source to | p. 8 | |
| [DC IN] jack. | the [DC13.8V] jack. The [DC IN] jack ac- |
| |
|
| cepts an AC adapter |
| |
|
|
|
| |
Receiver turns OFF by | • The sleep timer has been activated. | • Turn power back ON, then push | p. 29 | |
itself. |
| [SLEEP] one or more times to turn the |
| |
|
| sleep timer function OFF, if desired. |
| |
|
|
|
| |
No sound comes from | • Volume level is too low. | • Rotate [AF GAIN] clockwise to obtain a | — | |
the speaker. |
| suitable listening level. |
| |
| • The squelch is closed. | • Rotate [SQUELCH] counterclockwise to | p. 14 | |
|
| open the squelch. |
|
|
| • An external speaker or headphones are | • Disconnect the | external speaker or | — |
| connected. | headphones. |
|
|
| • CW narrow mode is selected when no | • Select another mode or install the op- | pgs. | |
| optional filter is installed. | tional CW narrow filter. | 13, 38 | |
|
|
|
| |
Sensitivity is low. | • The coaxial cable is cut. | • Fix the coaxial cable. | — | |
| • No antenna is connected. | • Connect an antenna. | p. 8 | |
| • The connected antenna is not matched | • Connect an antenna matched to the re- | p. 8 | |
| to the receive frequency. | ceiving frequency. |
| |
| • Wrong antenna connector is used for | • Check the antenna connection. | p. 8 | |
| V/UHF and HF antenna. |
|
|
|
| • Wrong antenna connector is selected in | • Select the proper antenna connector: | p. 31 | |
| set mode for HF antenna. |
| ||
| • An RF attenuator is activated. | • Push [ATT 10 dB] or [ATT 20 dB] to can- | — | |
|
| cel the function. |
|
|
|
|
|
| |
Receive signal is un- | • [IF SHIFT] is rotated too far CCW or | • Set [IF SHIFT] to the center position. | p. 14 | |
clear or distorted. | CW. |
|
|
|
| • [APF] is rotated too far CCW or CW. | • Set the [APF] control to the center position | p. 15 | |
|
| or push the [APF] switch to turn it OFF. |
| |
| • The wrong mode switch is pushed. | • Push the correct mode switch. | p. 13 | |
|
|
|
| |
WFM mode cannot be | • The operating frequency is lower than | • Set the frequency above 30 MHz when | p. 13 | |
set. | 30 MHz. (WFM mode cannot be se- | in WFM mode. |
|
|
| lected below 30 MHz.) |
|
|
|
Main dial does not func- | • The lock function is activated. | • Push [LOCK] for 1 sec. to deactivate. | p. 12 | |
tion. |
|
|
|
|
|
|
|
|
|
[LOCK] does not lock | • DIAL LOCK is selected in quick set | • Select PANEL | LOCK in quick set | p. 31 |
the keypad, function | mode. | mode. |
|
|
switches, etc. |
|
|
|
|
|
|
|
| |
The selected frequency | • The memory channel was changed be- | • Push [MW] for 1 sec. to write into a | p. 19 | |
is erased. | fore writing into memory. | memory before changing channels. |
| |
|
|
|
| |
The frequency is not | • An optional | • Install the | p. 38 | |
announced when push- | UNIT is not installed. |
|
|
|
ing [SPCH]. |
|
|
|
|
|
|
|
|
|
41