Manuals / ICP DAS USA / Computer Equipment / Network Card

ICP DAS USA 8830, 8KE8, 8KE4, 8430 user manual By SMMI Menu Network Configuration, Power, Mode, Down

Models: 8KE8 8830 8KE4 8430

1 90

Download 90 pages 20.92 Kb

Page 27

Image 27

2.1.3 By SMMI Menu: Network Configuration

Step3: Run the MiniOS7 Utility and click “Configuration”

Step4: Exit the MiniOS7 Utility and then restart the 8430/8830/8KE4/8KE8 for the new settings.

2.1.3 By SMMI Menu: Network Configuration

L1	L2	L3	POWER
MODE	UP	DOWN	SET

Step1: Accessing the SMMI menu

The LEDs normally show system information. Pressing the “Mode” and Set buttons for more than 1.5 seconds will allow access to the SMMI menu. The LED menu has 2 levels. By following the menu tree map, the cursor position in the SMMI menu can be changed.

8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 ----- 27

Page 27

Image 27

ICP DAS USA 8830, 8KE8, 8KE4, 8430 user manual By SMMI Menu Network Configuration, Power, Mode, Down

Contents

Version 1.0, January I-8430I-8830 I-8KE4-GI-8KE8-G8430/8830/8KE4/8KE8 Ethernet I/O Unit User’s Manual 8430/8830/8KE4/8KE8 Table of Contents Updating MiniOS7 image Download firmware8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Chapter 1. Introduction Various SDK provided free 1.1 FeaturesEthernet -based Data Acquisition I/O unit ASCII-based protocol DCON ProtocolInternet I/O configurable via the EthernetSimultaneous access by a maximum of 6 host PCs Updateable firmware via the RS-232 portDual Bus design to supports i-8K and i-87K series I/O modules More flexible I/O combination and Compact、fasten、quick to installInput Protection circuitry High performance integrated power supplyVentilated housing design to work between -25 ~+75 Built-in WatchdogEthernet port 1.2 i-8430/i-8830 Hardware SpecificationsSRAM EEPROMPower supply 20W DimensionMounting mechanism NVRAM 1.3 i-8KE4/i-8KE8 Hardware SpecificationsSRAM EEPROMPower supply 20W DimensionMounting mechanism RS-232/485 COM3 1.4 Front view of 8430/88308430 88308430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Pin assignment of COM1 Port Pin assignment of COM3 Port1.5 Front view of 8KE4/8KE8 8KE48KE8 8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Pin assignment of COM1 PortMethod b DIN-Rail mounting Frame Ground DIN-Rail Clips 1.6 8430/8830/8KE4/8KE8 installationStep2 Attach power supply 10 ~ 30 VDC The diagrams below show the basic wiring for the Ethernet I/O8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 33333 1111122222 444441.7 I/O module installation For I-8000 series modules the files are located atFor I-87K series modules the files are located at 8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Pin assignment8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Wire Connection8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Step2 Connect the wire Step3 Insert the I/O module into the 8KE4/8KE8By “Configuration Wizard“ By “MiniOS7 Utility” By “SMMI Menu” Chapter 2. Configure the 8430/8830/8KE4/8KE8 and I/O modules2.1 Configure the network settings 2.1.1 By “Configuration Wizard”4.1 4.2 4.21 2.1.2 By MiniOS7 UtilityDOWN 2.1.3 By SMMI Menu Network ConfigurationPOWER MODEStep2 The SMMI menu tree Following is the SMMI menu tree Cursor position8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Step3 Selection items that can be changed 2.3 Configure I/O modules 2.2 Creating a virtual COM port to map the I/O modulesDCON Utility 8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 3.1 4.1 4.2 4.38430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Chapter 3. Using the DCON Protocol 3.1 The feature of using DCON Protocol8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Step 3. Receive data from Ethernet controller 3.2 Using the TCP protocol directlyStep 2. Send command with cr Step 1. Connect to the Ethernet controllerThe result will be as below 8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 3.3 Via VxComm technology4.1 Location of documents and software Chapter 4. Software Development ToolKit free8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 The diagram below show the architecture of the SDKDCON Utility DOS version 4.2.1 Procedure for using the DCON Utility DOSDCON Utility DOS 4.2 DCON Utility DOSDCON DLL 4.3.1 Procedure for using the DLL4.3 DCON DLL DLL libraryQuickStartManual.pdf FAQ.pdf4.3.2 VB Example Reading an analog input value VB Step VB Step VB Step Step 7 Write the program code8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Step 8 Run the projectActiveX ocx component Supported modules 4.4.1 Procedure for using the ActiveXDCON ActiveX 4.4 DCON ActiveX4.4.2 VB Example Reading an analog input value InstallOCX.pdfStep 4 Run VB and create a new project .exe project Step 5 Add the ActiveX ocx component to the project8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Step 6 Arrange all the components on the formStep 7 Write the program code VB Step VB Step VB Step8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Step 8 Run the projectDCON LabVIEW 4.5.1 Procedure for using DCONLabVIEW4.5 DCON LabVIEW Bundled driver for LabVIEWDCONDLL.pdf Descriptions of all sub-function in DCONDLL CallDLLinLabVIEW.pdf Explains how to call a sub-vi of in LabVIEW8000Demo Demo programs for I-8000 I/O modules 8000.llb LabVIEW library contains all sub-vi for I-8000 I/O modules8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Step3 Select the sub-vi form Functions Palette Select a VI…8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 4.5.2 LabVIEW Example Reading multi-channel analog Input valueStep4 Select the target *.lib file LabVIEW library file Step5 Select the desired sub-vi4.5.2 LabVIEW Demo Program Reading multi-channel analog input value Step7 Draw the data flow of sub-vi8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 2.1 2.2Step2 Set the parameters Step3 Run the demoDCON Indusoft 4.6.1 Procedure for using the Indusoft bundled driver4.6 DCON Indusoft 4.6.2 Indusoft Example Reading an analog input valueStep 5 Include the DCON driver 5.1 5.2 5.3 5.4Step 3 Run the DCON Utility to configure the I/O modules Step 4 Run Indusoft and create a new project8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Step 6 Configure the DCON driverStep8 Arrange all the components on the form 7.1 7.2Step7 Insert tags to connect to I/O modules The address format is Address ModuleID Slot Channel8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 9.1 9.2Step9 Double click the text box to assign a tag to it Step10 Run the projectOPC Server 4.7 NAP OPC Server4.7.1 Introduction NAP OPC server4.7.2 Procedure for using the OPC server 4.7.3 OPC Server Example Reading an analog input value 4.1 4.2 4.4 4.3 Step 4 Run the OPC server to search for I/O modules on COM38430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Labview National WIZCON iFix Indusoft CitectStep 5 Save the configuration and close the OPC Server Step 6 Run SCADA software to connect to the OPC ServerTop View Appendix A Dimensionsi-8430 Back ViewTop View i-8830Back View Side ViewFront View i-8KE4Back View Top ViewTop View i-8KE8Back View Side ViewBasic Command Format Appendix B DCON protocolFrequently used Command table reference B.1 Command SetCommand #01S3+2.1234+2.1234 +2.1234 +2.1234 cr +2.1234+2.1234 +2.1234 +2.1234Description #01S3C0+2.1234cr CommandDescription #01S3C1+09.000#01S3C1-05.000 CommandValid Command CommandA Command to read the data commandDescription #01S30042#01S300AA55cr Command8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 Description #01S31C01#01S31A00cr CommandChannel Status CommandCommand DescriptionB.2 Hardware interface Use Virtual COM Port interface Appendix C VxComm technique8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 The two application architectures are shown as belowAppendix D i-8K and i-87K series I/O modules i-87K series i-8000 seriesAppendix E Updating firmware and MiniOS7 image E.1 Access the controller Power 10~ 30 VDCCA-0915 6.1 6.2 Step5 Run MiniOS7 Utility Step6 Select the COM port of the host PC8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 8430/8830/8KE4/8KE8 User’s manual, Jan 2005, Version 1.0, 8MS-002-10 2. List files in the Flash ROM 1. MiniOS7 image informationi. MiniOS7 image version of the 8430/8830/8KE4/8KE8 ii. Files in the Flash ROME.2 Updating MiniOS7 image 2.1 2.2 E.3 Download firmware