Integra DTR-5.5 instruction manual Controlling Other Components, Entering Remote Control Codes

DTR-6.5,5.5_En.book Page 80 Wednesday, July 28, 2004 9:07 AM

Controlling Other Components

You can use the AV Receiver’s remote controller (RC- 588M/RC-590M/RC-591M) to control your other com- ponents, including those made by other manufacturers. This chapter explains how to:

•Enter the remote control code for a component that you want to control (e.g., DVD, TV, VCR).

•Learn commands directly from another component’s remote controller (see page 88).

•Program the Macro function to perform a sequence of actions with a single press of a button (see page 89).

Entering Remote Control Codes

2

	Remote Mode
Receiver	DVD	C D	MD/CDR
Tape
T V	VCR	Cable	SAT

Standby

While holding down the Remote Mode button that you want to enter the code for, press the [Standby] button.

Entering the appropriate remote control code for each Remote Mode button will allow you to control your other components with the remote controller.You’ll need to perform this procedure for each component that you want to control.

For the [DVD], [TV], [VCR], [CABLE], and [SAT] but- tons, choose a code from the respective category. For the [CD] and [MD/CDR] buttons, you can choose a code from any category. Remote control codes cannot be entered for the [Receiver] and [ZONE 2] buttons.

2	On	Standby					T V
					I		Input
	V1		V 2		V 3
	1		2		3		+
	V4	Multi CH			DVD		TV CH
3	4		5		6		-
	CD		Tape		Tuner
	7		8		9
	Phono						TV VOL
	+10		0		Clear
	--/---	Input Selector
		Macro
	1		2		3		Zone 2
			Remote Mode
2	Receiver		DVD		CD		MD/CDR
	Tape
	TV		VCR		Cable		SAT
	Dimmer						Sleep
	TV		enu		M
			pM		en
	Input	o				u
		T
	+
	CH			Enter			VOL
	Disc
	-		E		e
				xit
					id
	Prev				Gu
		R	eturn			p
	CH				Setu
	Display						Muting

1	Look up the remote control code
	for your component.
	See “Remote Control Codes” on
	page 82.

3			Within 30 seconds, use the num-
V1 V 2		V 3	ber buttons to enter the 4-digit
			remote control code.
1	2	3
V4	Multi CH	DVD
4	5	6
CD	Tape	Tuner
7	8	9
	0

4	Select the remote controller
	mode, point the remote control-
	ler at the component, and check
	its operation.
	Remote controller buttons that can be
	used in DVD mode are shown on
	page 16. Those that can be used with
	the TV, VCR, CABLE, and SAT modes
	are shown on pages 86, 87.

If the remote controller works OK, the code has been entered correctly. If not, try again or try another code.

Codes for Integra DVD Players

The remote control code for an Integra DVD player

depends on whether it’s connected via , as follows:

5001: Use this code if you’ve connected an cable and an analog audio cable to your DVD player. This is the default setting, so if you’re using , you don’t need to change anything. Point the remote controller at the AV receiver to operate the DVD player.

5002: Use this code if your DVD player doesn’t have

an jack, or you’re not using . Point the remote controller at the DVD player to operate it.

Setting the [MD/CDR] Button to CDR

By default, the [MD/CDR] button is set to control a MiniDisc recorder. To control a CD recorder, it must be set to CDR. The codes are as follows:

6002: Code for controlling an CD recorder.

6003: Code for controlling an MD recorder (default).

80