Integra DTR-7.3 Connecting to Audio/Video equipment, Connecting video camera, etc. VIDEO 5 INPUT

Connecting to Audio/Video equipment

8.Settop box, video camera (VIDEO 3)

S Video output
Video output
	L (white)
Analog audio
output	R (red)

Digital audio output (optical)

: Signal flow

DIGITAL		PR		AUDIO	VIDEO	S VIDEO	COMPONENT
INPUT		RNA					VIDEO
COAX						MONITOR	OUTPUT
1						OUT	Y
			R	L
	SUB
2			AM	OUT		ZONE 2	PB
	SURR
3				IN		DVD	PR
	SURR	R
OPT	BACK/						INPUT 1
	ZONE 2								9. Satellite tuner or television
1			FM	OUT			Y
								ETHERNET
			75							(VIDEO 4)
						VIDEO 1		[NET-TUNE]
	FRONT			IN			PB	CE
2
		O						SP
	R	L						CAUTION:
	SUB							SPEAKER
3			PHONO	OUT			PR	IMPEDANCE
						VIDEO 2		4 OHMS MIN. OR
	SURR						INPUT 2	6 OHMS MIN.
								/SPEAKER
DIGITAL			CD	IN			Y	SEE INSTRUCTION		S Video output
OUTPUT		R						MANUAL FOR
			OUT					CORRECT SETTING
OPT	SURR			IN		VIDEO 3	PB
	BACK		TAPE							Video output
				IN		VIDEO 4	PR
	GND		IN	L					L (white)
		L	R		VIDEO	S VIDEO
		O		AUDIO
										Analog audio
									R (red)	output

8, 9. Connecting a satellite tuner, television, or settop box (VIDEO 3 or 4)

Using an RCA video cable, connect the video output jack (composite) of the device to the VIDEO 3 (or 4) VIDEO IN jack of the DTR-7.3. Or if the device has an S video output jack, connect it to the VIDEO 3 (or 4) S VIDEO IN jack of the DTR-7.3 using an S video cable. Or if the device has component video outputs, connect them to one of the banks of COMPONENT VIDEO INPUT jacks on the DTR-7.3.

With the initial settings of the DTR-7.3, the VIDEO 3 and 4 input sources are set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the device to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at Setup Menu → Input Setup → Video Setup → Component Video (see page 48).

Using an RCA audio cable, connect the audio output jack of the device to the VIDEO 3 (or 4) AUDIO IN jacks of the DTR-7.3. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the device has a digital output, connect it to either the DIGITAL INPUT COAX jack or DIGITAL INPUT OPT jack of the DTR-7.3 depending on the type of connector on the device.

With the initial settings of the DTR-7.3, the VIDEO 3 input source is set for digital input at the OPT 3 jack.

If the digital connection is made at a different jack, this must be changed at Setup Menu → Input Setup → Digital Setup (see page 46).

With the initial settings of the DTR-7.3, the VIDEO 4 input source is not set for digital input. If you are connecting a digital component, these settings must be changed at Setup Menu → Input Setup → Digital Setup (see page 46).

10. Connecting video camera, etc. (VIDEO 5 INPUT)

Using an RCA video cable, connect the video output jack (composite) of the device to the VIDEO 5 VIDEO jack of the DTR-

7.3.Or if the device has an S video output jack, connect it to the VIDEO 5 S VIDEO jack of the DTR-7.3 using an S video cable.

Using an RCA audio cable, connect the audio output jack of the device to the VIDEO 5 AUDIO jacks of the DTR-7.3. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the device has an optical digital output, connect it to the VIDEO 5 DIGITAL jack of the DTR-7.3.

The VIDEO 5 digital input is fixed to the OPTICAL input on the front panel.

Front panel

S Video output

Digital output (optical)

10.Video camera/ Video game (VIDEO 5 INPUT)

Video output

L

Analog output

R

19