Manuals / Intel / Computer Equipment / Switch

Intel 1000LX, 1000SX manual 62.5 μm MMF up to 550 m 1804 ft†

Models: 1000LX 1000SX

1 30

Download 30 pages 17.35 Kb

Page 23

C H A P T E R 4 Specifications

1000LX Physical	The 1000LX Module has the following specifications:
speciﬁcation

	Number of ports:	Three: 2 x Stack Interface Module
		and 1 x 1000Base-LX

	Connector Types:
	Stack Interface Module	26-position shielded plug
	1000Base-LX	Duplex SC

	Cable Types:
	Stack Interface Module	Stacking Cable (ES500SC)
	1000Base-LX	50 μm multi-mode ﬁber (MMF)
		62.5 μm multi-mode ﬁber (MMF)
		10.0 μm single-mode ﬁber (SMF)

	Link Lengths:
	Stack Interface Module	1 meter (39 inches)
	1000Base-LX	50 μm MMF up to 550 m (1804 ft)†
		62.5 μm MMF up to 550 m (1804 ft)†
		10 μm SMF up to 5000 m (16404 ft)

	Default Settings:	Stack mode
		Auto-negotiation: enabled
		Spanning Tree: disabled

	Dimensions	Width: 149mm (5.9in.)
		Height: 37mm (1.5in.)
		Depth: 238mm (9.4in.)

	Weight (approximate)	0.235kg (0.63 lb)

Note † To achieve these connections, a single-mode offset-launch mode-conditioning patch cord must be included on the TX cable (for full details, see IEEE 802.3z and the table below):

	Description	62.5 μm	50 μm	Unit
	Description	MMF	MMF	Unit
		MMF	MMF

	Maximum insertion loss	0.5	0.5	dB

	Coupled Power Ratio	28<CPR<40	12<CPR<20	dB
	(CPR)	28<CPR<40	12<CPR<20	dB
	(CPR)

	Optical center offset	17<Offset<23	10<Offset<16	μm
	between SMF and MMF	17<Offset<23	10<Offset<16	μm
	between SMF and MMF

	Maximum angular offset	1	1	degree

20

Image 23

Intel 1000LX, 1000SX manual 62.5 μm MMF up to 550 m 1804 ft†

Contents

User Guide 1000SX Module and 1000LX Module for 500 Series Switches715236-001 1000SX Module and 1000LX Module for 500 Series SwitchesUser Guide 715236-001 Year 2000 capableFirst edition OctoberLASER PRODUCT Quick StartCLASS LASER PRODUCT CLASSNaming in this Quick Start This Quick Start covers two products 5 Turn on the switch Conﬁgure and cable the Configure the module using Intel Device View and cable up using 1000SX and 1000LX Modules Introduction Indicates Module LEDsStatus Page automatically saved and Intel Device View resets the Conﬁgure the module and connect the cablesThe configuration and cabling of the 1000Base Module are very Note When the module mode is changed, the conﬁguration isC H A P T E R 3 Configure the module and connect the cables Conﬁguring the ModuleStand-alone Mode Cabling the ModuleCabling to a Matrix Module in a group of switches Stack ModeNote Redundancy is not possible with the 510T 3 Plug the other end of the Stacking Cable into an empty port on the Matrix Module located on the same side of the switch for example, both modules in Slot A, and secure it using the latches on the connector Introduction Prevent network loops Link Aggregation with Two Modulesules in Slot A Server Page Speciﬁcations 62.5 μm 62.5 μm MMF up to 550 m 1804 ft†Returning a Defective Product RMA Limited Hardware WarrantyLimited Hardware Warranty Returning a Defective Product RMA Limited Hardware Warranty Europe onlyA P P E N D I X A Limited Hardware Warranty LIMITATION OF LIABILITY AND REMEDIESNumber A Limited Hardware WarrantyA P P E N D CountryManufacturer Declaration WARNING Fiber-optic ports on 1000SX-Optical SafetyWARNING Fiber-optic ports on 1000LX-Optical Safety Federal Communications Commission FCC StatementA P P E N D I X A Limited Hardware Warranty AVERTISSEMENTWARNUNG A P P E N D I X A Limited Hardware Warranty AVVERTENZAADVERTENCIAS Country Automated SupportCustomer Support Technicians North America only