Electrical Specifications
58 Datasheet
Notes:
1. 00h = Off State
2. VID Range HEX 01-32 are not used by the processor.
3. For VID Ranges supported, see Table 7-10.
4. VCCD is a fixed voltage of 1.35V or 1.5V.

7.1.9 Reserved or Unused Signals

All Reserved (RSVD) signals must not be connected. Connection of these signals to VCC,

VTTA, VTTD, VCCD, VCCPLL, VSS, or to any other signal (including each other) can result in

component malfunction or incompatibility with future processors. See Chapter 8 for a

land listing of the processor and the location of all Reserved (RSVD) signals.

For reliable operation, always connect unused inputs or bi-directional signals to an

appropriate signal level. Unused active high inputs should be connected through a

resistor to ground (VSS). Unused outputs may be left unconnected; however, this may

interfere with some Test Access Port (TAP) functions, complicate debug probing, and

prevent boundary scan testing. A resistor must be used when tying bi-directional

signals to power or ground. When tying any signal to power or ground, a resistor will

also allow for system testability.

7.2 Signal Group Summary

Signals are grouped by buffer type and similar characteristics as listed in Table 7-5. The

buffer type indicates which signaling technology and specifications apply to the signals.

Note:
1. Qualifier for a buffer type.
4D 0.63000 70 0.80500 93 0.98000 B6 1.15500 D9 1.33000 FC 1.50500
4E 0.63500 71 0.81000 94 0.98500 B7 1.16000 DA 1.33500 FD 1.51000
4F 0.64000 72 0.81500 95 0.99000 B8 1.16500 DB 1.34000 FE 1.51500
50 0.64500 73 0.82000 96 0.99500 B9 1.17000 DC 1.34500 FF 1.52000
51 0.65000 74 0.82500 97 1.00000 BA 1.17500 DD 1.35000
52 0.65500 75 0.83000 98 1.00500 BB 1.18000 DE 1.35500
53 0.66000 76 0.83500 99 1.01000 BC 1.18500 DF 1.36000
54 0.66500 77 0.84000 9A 1.01500 BD 1.19000 E0 1.36500

Table 7-3. VR12.0 Reference Code Voltage Identification (VID) Table (Sheet 2 of 2)

Hex VCC, VSA,
VCCD
Hex VCC, VSA,
VCCD
Hex VCC, VSA,
VCCD
Hex VCC, VSA,
VCCD
Hex VCC, VSA,
VCCD
Hex VCC, VSA,
VCCD

Table 7-4. Signal Description Buffer Types

Signal Description
Analog Analog reference or output. May be used as a threshold voltage or for buffer
compensation
Asynchronous Signal has no timing relationship with any system reference clock.
CMOS CMOS buffers: 1.0V or 1.5V tolerant
DDR3 DDR3 buffers: 1.5V and 1.35V tolerant
DMI2 Direct Media Interface Gen 2 signals. These signals are compatible with PCI Express*
2.0 and 1.0 Signaling Environment AC Specifications.
Open Drain CMOS Open Drain CMOS (ODCMOS) buffers: 1.0V tolerant
PCI Express* PCI Express* interface signals. These signals are compatible with PCI Express 3.0
Signalling Environment AC Specifications and are AC coupled. The buffers are not
3.3-V tolerant. Refer to the PCI Express specification.
Reference Voltage reference signal.
SSTL Source Series Terminated Logic (JEDEC SSTL_15)