Manuals / Intel / Computer Equipment / Computer Hardware

Intel Demo Board with FPGA for SS-SMII (Fiber)-to-MII Conversion manual Introduction, Overview

Models: 249323-003 Demo Board with FPGA for SS-SMII (Fiber)-to-MII Conversion

1 40

Download 40 pages 30.63 Kb

Page 9

LXD9785 PQFP Demo Board with FPGA for SS-SMII (Fiber)-to-MII Conversion

2.0Introduction

2.1Overview

This document describes typical hardware set-up procedures for the LXD9785 PQFP MII Demo Board. To begin immediate operation, a “Quick-Start Checklist” on page 12 supports 100BASE- FX operation.

Hardware switches and jumpers allow the designer access to all hardware configuration options. Each option is outlined in the “Optional Configurations” on page 14.

The Demo Board provides two sets of LED indicators: Direct Drive LEDs and Inter Frame Status per-port LEDs. The Direct Drive LEDs can be used to display speed, transmit and receive activities, collision condition, link status, duplex mode, and isolate condition. The Inter Frame Status LEDs can be used to display full-duplex or half-duplex, 10 Mbps or 100 Mbps, or link.

Board schematics and a Bill of Materials are located in the back of the document.

2.2Equipment Requirements

The LXD9785 Demo Board is populated with all of the IC components needed for twisted-pair evaluation. However, the following additional equipment is also required:

•SmartBits Advanced Multi-port Performance Test Box

•PC with Smart Windows (version 6.51 or newer) installed.

•A 3.3V DC Power Supply.

•A 2.5V DC Power Supply.

•Eight MII Cables (male-to-male).

•Eight external NIC cards.

•Eight fiber cables.

2.3Fiber Register Configuration

For a register setup via MDIO, proceed with the configuration of the device by setting Register Bit 16.0 to 1 for all ports (see Table 5).

Development Kit Manual

9

Document #: 249323

Revision #: 003

Rev. Date: January 24, 2002

Image 9

Intel Demo Board with FPGA for SS-SMII (Fiber)-to-MII Conversion manual Introduction, Overview, Equipment Requirements

Contents

Development Kit Manual LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionJanuary Document # Revision # Rev. Date January Copyright Intel CorporationContents FiguresContents Contents TablesContents Revision HistoryDate RevisionPage 1.0 General Description 1.1 FeaturesLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Development Kit ManualLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Figure 1. LXD9785 PQFP MII Demo BoardDevelopment Kit Manual Document # 249323 Revision # 003 Rev. Date January2.0 Introduction 2.3 Fiber Register Configuration2.1 Overview 2.2 Equipment RequirementsFigure 2. Typical Test Setup 2.4 Typical SetupSmartBits Demo BoardLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Figure 3. LXD9785/9785E SS-SMII Fiber Demo BoardDevelopment Kit Manual Document # Revision # Rev. Date January 243.0 Quick-Start Checklist Table 1. Quick-Start Jumper SettingsLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Switch / Label Table 2. Quick-Start Switch SettingsSetting Configuration4.1 Global Operating Configurations 4.0 Optional Configurations4.2 MII Address Configurations Table 3. Global Configuration Settings Switch S5Table 5. PHY Address Configuration Settings Switch S1 4.3 Alternate MDIO Routing ConfigurationTable 6. MDIO Routing Port LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionTable 7. JTAG Test Signal Descriptions 4.4 JTAG Test Signals4.5 Extended Temperature Operation with the LXT9785HE LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion5.0 LEDs Table 8. Direct Drive LED Configuration Settings Register5.1 Direct Drive LEDs LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionTable 9. LED Pulse Stretch Settings Register 5.2 Inter Frame Status LEDsLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Figure 4. LXD9785 PQFP MII Demo Board Power Fiber Board Revision A2 6.0 Board SchematicsLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Development Kit ManualMDINT Development Kit ManualREMOVE MODELXD9785 Figure 6. MII Ports 0 andPQFP Demo Board with FPGA for SS-SMIIRev. Date January Development Kit ManualFiber-to LXD9785 SS/SMII MII FX DV BOARDDevelopment Kit Manual Figure 8. MII Ports 4 andLXD9785 PQFPRev. Date January Development Kit ManualLXD9785 SS/SMII MII FX DV BOARD Figure 9.MIIPorts6andLXD9785 PQFP Figure 10. Fiber Ports 0 andDevelopment Kit Manual Demo Board with FPGA for SS-SMIIKit Manual FPGA for SS-SMII Fiber-toConversion Date JanuaryDevelopment Kit Manual Figure 12. Fiber Ports 4 andLXD9785 PQFP Demo Board with FPGA for SS-SMIILXD9785 PQFP Demo Board with Figure 13. Fiber Ports 6 andDevelopment Kit Manual FPGA for SS-SMII Fiber-toBoard Development Kit ManualSMII withLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Figure 15. SS-SMII to MII ALTERADevelopment Kit Manual Document # 249323 Revision # 003 Rev. Date JanuaryDevelopment Kit Manual Figure 16. Clock DistributionLXD9785 PQFP Demo Board with FPGA for SS-SMIILEDs Figure 17. Inter-Frame StatusFPGA for SS-SMII Fiber-toDevelopment Kit Manual PQFP Demo Board with FPGA for SS-SMIILXD9785 Fiber-toLXD9785 PQFP Demo Board with FPGA Figure 19. MDIO0 and MDC0 FixINSTALL R614 Development Kit ManualMDC1 Fix Figure 20. MDIO1 andLXD9785 PQFPTable 10. LXD9785 Bill of Materials Fiber - SS-SMII 7.0 Bill of MaterialsLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Development Kit ManualLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Table 10. LXD9785 Bill of Materials Fiber - SS-SMII ContinuedDevelopment Kit Manual Reference DesignatorTable 10. LXD9785 Bill of Materials Fiber - SS-SMII Continued LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionDevelopment Kit Manual Reference DesignatorTable 10. LXD9785 Bill of Materials Fiber - SS-SMII Continued LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionDevelopment Kit Manual Reference Designator