Manuals / Intel / Computer Equipment / Computer Hardware

Intel 249323-003 manual Quick-Start Checklist, Quick-Start Jumper Settings

Models: 249323-003 Demo Board with FPGA for SS-SMII (Fiber)-to-MII Conversion

1 40

Download 40 pages 30.63 Kb

Page 12

LXD9785 PQFP Demo Board with FPGA for SS-SMII (Fiber)-to-MII Conversion

3.0Quick-Start Checklist

Use this quick-start procedure for easy setup of the LXD9785 PQFP MII Demo Board. This procedure sets all ports to the default condition (100 Mbps and full-duplex capabilities).

1.Set the jumpers in accordance with Table 1.

2.Set switches S1, S5, and S8 in accordance with Table 2.

3.Connect the eight Demo Board MII ports to the SmartBits test box via MII connector/cables. Male-to- male connectors are required to interface the SmartBits test box to the LXD9785 PQFP MII Demo Board and are available from Newark (.5m cable - Newark P/N 91F9746).

4.Connect the fiber ports to external NIC cards via fiber cables. Each NIC card plugs directly into the SmartBits test box.

5.Connect +2.5V DC power to VCC and a +3.3V DC power supply to VCCIO and VCC-EXT.

6.With the Demo Board appropriately configured, apply power to the LXD9785 PQFP MII Demo Board and press Reset switch S4.

7.Proceed with evaluation as desired.

Table 1. Quick-Start Jumper Settings

	Jumper / Label	Setting	Configuration

	JP1 / MDIO	Jumper Pins	Routes MDIO through Port 0 MII Connector.
	JP1 / MDIO	2 & 3	Routes MDIO through Port 0 MII Connector.
		2 & 3

	JP2 / MDC	Jumper Pins	Routes MDC through Port 0 MII Connector.
	JP2 / MDC	2 & 3	Routes MDC through Port 0 MII Connector.
		2 & 3

	JP12 / SD Interface	Open	Enables 3.3V SD Fiber interface.

	JP13	Jumpered	Provides voltage to Fiber transceivers.

	JP15	Jumper Pins	Enables 1x8 mode.
	JP15	2 & 3	Enables 1x8 mode.
		2 & 3

	JP16	Jumper Pins	Enables 2x4 mode.
	JP16	1 & 2	Enables 2x4 mode.
		1 & 2

12	Development Kit Manual

Document #: 249323 Revision #: 003 Rev. Date: January 24, 2002

Image 12

Intel 249323-003 manual Quick-Start Checklist, Quick-Start Jumper Settings

Contents

Development Kit Manual LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionJanuary Copyright Intel Corporation Document # Revision # Rev. Date JanuaryContents FiguresContents Tables ContentsRevision History ContentsDate RevisionPage 1.1 Features 1.0 General DescriptionLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Development Kit ManualFigure 1. LXD9785 PQFP MII Demo Board LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionDevelopment Kit Manual Document # 249323 Revision # 003 Rev. Date January2.3 Fiber Register Configuration 2.0 Introduction2.1 Overview 2.2 Equipment Requirements2.4 Typical Setup Figure 2. Typical Test SetupSmartBits Demo BoardFigure 3. LXD9785/9785E SS-SMII Fiber Demo Board LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionDevelopment Kit Manual Document # Revision # Rev. Date January 243.0 Quick-Start Checklist Table 1. Quick-Start Jumper SettingsLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Table 2. Quick-Start Switch Settings Switch / LabelSetting Configuration4.0 Optional Configurations 4.1 Global Operating Configurations4.2 MII Address Configurations Table 3. Global Configuration Settings Switch S54.3 Alternate MDIO Routing Configuration Table 5. PHY Address Configuration Settings Switch S1Table 6. MDIO Routing Port LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion4.4 JTAG Test Signals 4.5 Extended Temperature Operation with the LXT9785HETable 7. JTAG Test Signal Descriptions LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionTable 8. Direct Drive LED Configuration Settings Register 5.0 LEDs5.1 Direct Drive LEDs LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionTable 9. LED Pulse Stretch Settings Register 5.2 Inter Frame Status LEDsLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion 6.0 Board Schematics Figure 4. LXD9785 PQFP MII Demo Board Power Fiber Board Revision A2LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Development Kit ManualDevelopment Kit Manual MDINTREMOVE MODEFigure 6. MII Ports 0 and LXD9785PQFP Demo Board with FPGA for SS-SMIIDevelopment Kit Manual Rev. Date JanuaryFiber-to LXD9785 SS/SMII MII FX DV BOARDFigure 8. MII Ports 4 and Development Kit ManualLXD9785 PQFPDevelopment Kit Manual Rev. Date JanuaryLXD9785 SS/SMII MII FX DV BOARD Figure 9.MIIPorts6andFigure 10. Fiber Ports 0 and LXD9785 PQFPDevelopment Kit Manual Demo Board with FPGA for SS-SMIIFPGA for SS-SMII Fiber-to Kit ManualConversion Date JanuaryFigure 12. Fiber Ports 4 and Development Kit ManualLXD9785 PQFP Demo Board with FPGA for SS-SMIIFigure 13. Fiber Ports 6 and LXD9785 PQFP Demo Board withDevelopment Kit Manual FPGA for SS-SMII Fiber-toDevelopment Kit Manual BoardSMII withFigure 15. SS-SMII to MII ALTERA LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionDevelopment Kit Manual Document # 249323 Revision # 003 Rev. Date JanuaryFigure 16. Clock Distribution Development Kit ManualLXD9785 PQFP Demo Board with FPGA for SS-SMIIFigure 17. Inter-Frame Status LEDsFPGA for SS-SMII Fiber-toPQFP Demo Board with FPGA for SS-SMII Development Kit ManualLXD9785 Fiber-toFigure 19. MDIO0 and MDC0 Fix LXD9785 PQFP Demo Board with FPGAINSTALL R614 Development Kit ManualFigure 20. MDIO1 and MDC1 FixLXD9785 PQFP7.0 Bill of Materials Table 10. LXD9785 Bill of Materials Fiber - SS-SMIILXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Development Kit ManualTable 10. LXD9785 Bill of Materials Fiber - SS-SMII Continued LXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII ConversionDevelopment Kit Manual Reference DesignatorLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Table 10. LXD9785 Bill of Materials Fiber - SS-SMII ContinuedDevelopment Kit Manual Reference DesignatorLXD9785 PQFP Demo Board with FPGA for SS-SMII Fiber-to-MII Conversion Table 10. LXD9785 Bill of Materials Fiber - SS-SMII ContinuedDevelopment Kit Manual Reference Designator