Manuals / Intel / Computer Equipment / Computer Hardware

Intel MS-6112 Chapter, Introduction, Dimension, lATX Form Factor 30cmL x 23cmW x 4 layers PCB

Models: MS-6112

1 68

Page 4

CHAPTER 1	INTRODUCTION

Dimension

lATX Form Factor: 30cm(L) x 23cm(W) x 4 layers PCB.

lDouble deck I/O connectors, compatible with Intel® Venus Mainboard.

Mounting

l9 mounting holes.

1-4

Page 4

Image 4

Intel MS-6112 Chapter, Introduction, Dimension, lATX Form Factor 30cmL x 23cmW x 4 layers PCB, Mounting, l9 mounting holes

Contents

Chapter INTRODUCTION 1.1 Mainboard Features Switching Voltage RegulatorChip Set Clock GeneratorBIOS Keyboard ConnectorOn-BoardIDE On-BoardPeripheralsDimension CHAPTERINTRODUCTION lATX Form Factor 30cmL x 23cmW x 4 layers PCB1.2 Mainboard Layout MS-6112BIOS SLOTChapter HARDWARE INSTALLATION 2.1 Central Processing Unit CPU2.1-1CPU Installation Procedures Required ThingsHSSBASE RM HSSPIN RMAMHSSTOP Page CHAPTER CHAPTER HARDWARE INSTALLATION Step 6 Install the ProcessorCHAPTER Step 7 Lock the Processor LocksHARDWARE INSTALLATION Step 8 Install the Heat Sink Support Top BarThe installation is now complete CHAPTERCHAPTER HARDWARE INSTALLATION Step 3 Install the Heat Sink Support BaseCHAPTER Retention Mechanism Notch HoleHARDWARE INSTALLATION Step 4 Install the Heat Sink SupportCHAPTER Intel Boxed PentiumTM Processor Heat Sink SupportCHAPTER HARDWARE INSTALLATION The installation is now completeCHAPTER PC-37452.1-2CPU Speed Setting SW1 Type200MHz 233MHz2.1-3CPU Clock Generator Setting J10/J9 HARDWARE INSTALLATIONCHAPTER These jumper is used to set the CPU Clock2.1-4CPU Fan Power Connectors JFAN/CFAN1/SFAN1 PSFAN1Voltage Setting 2.2 Flash ROM Programming Voltage JMODE1+12V PWD VCC +12V2.3 External Battery Connector JBAT1 2.4 Memory Installation 2.4-1Memory Bank Configuration2.4-2Memory Installation Procedures Single Sided DIMM Double Sided DIMMA. How to install a DIMM Module 2-202.4-1Memory Population Rules HARDWARE INSTALLATIONCHAPTER 1.Supports EDO and SDRAMTable 2.4-1EDO DRAM Memory Addressing Table 2.4-2SDRAM Memory Addressing2.5 Case Connector JFP1 PowerReset Switch2.5-2Reset Switch 2.5-4Power LED2.5-1Turbo LED 2.5-3KeylockHARDWARE INSTALLATION 2.6 Floppy Disk Connector FDCCHAPTER 2.7 Hard Disk Connectors IDE1 & IDE2 2.8 Power Supply 2.8-1ATX 20-pinPower Connector JPWR1SIGNAL SIGNAL2.8-2Remote Power On/Off Switches JSW1/JSW2 2.9 IrDA Infrared Module Connector IR1 HARDWARE INSTALLATIONCHAPTER 1 VCC NC IRRX GND IRTXPIN DEFINITION 2.10 Serial Port Connectors COM A & COM BSIGNAL 2.11 Parallel Port Connector LPT SIGNALSIGNAL PIN DEFINITION2.12 Mouse Connector: JKBMS1 2.13 Keyboard Connector JKBMS1SIGNAL 2.14 USB Connector USB2-33 HARDWARE INSTALLATION 2.15 Power Saving LED Connector JGL1CHAPTER HARDWARE INSTALLATION 2.16 Special Jumpers J3/J4CHAPTER AMI BIOS USER’S GUIDE Chapter AMI BIOS USER GUIDECHAPTER 3.1 Enter BIOS Setup CHAPTER 3.2 Standard CMOS Setup 3.3 Advanced CMOS Setup Quick Boot 1st Boot Device/2nd Boot Device/3rd Boot DeviceTry other Boot Devices Floppy Access ControlBoot up Num Lock Password CheckFloppy Drive Swap Floppy Drive SeekBoot to OS/2 System BIOS CacheableParity Check Internal Cache/External CacheCHAPTER 3.4 Advanced Chipset Setup Auto Configure EDO DRAM Timing EDO RAS to CAS DelaySDRAM RAS to CAS Delay EDO DRAM Speed nsSDRAM CAS Latency SDRAM RAS Precharge TimeDRAM Integrity Mode VGA Frame Buffer USWCPCI Frame Buffer USWC DRAM Refresh QueueFixed Memory Hole CPU To PCI IDE PostingPIIX4 Delayed Transaction AGP Aperture SizeUSB Passive Release PIIX4 Passive ReleaseUSB Function USB Keyboard Legacy SupportAMI BIOS USER’S GUIDE CHAPTER3.5 Power Management Setup Power Management/APM Green PC Monitor Power StateVideo Power Down Mode Hard Disk Power Down ModeStandby Time Out Suspend Time OutThrottle Slow Clock Ratio Modem Use IO PortRTC Alarm Resume From Soft-Off Power Button FunctionRing Resume from Soft-Off 3.6 PCI/Plug and Play Setup PCI Latency Timer PCI Clocks Plug and Play Aware O/SPCI VGA Palette Snoop Allocate IRQ to PCI VGAPCI IDE BusMaster Offboard PCI IDE CardOffboard PCI IDE Primary IRQ Offboard PCI IDE Secondary IRQIRQ3/IRQ4/IRQ5/RQ7/IRQ9/IRQ10/IRQ11/IRQ14/IRQ15 DMA Channel 0/1/3/5/6/7Reserved Memory Size/Reserved Memory Address 3.7 Peripheral Setup Onboard FDC Onboard Serial Port A/Onboard Serial Port BDescription of the item on screen follows If the ISA add-oncard hasIR Port Support IR Base Address SelectIR IRQ Select IR DMA SelectEPP Version Parallel Port ModeParallel Port IRQ Parallel Port DMA ChannelAMI BIOS USER’S GUIDE 3.8 Hardware Monitor SetupCHAPTER