Manuals / Intel / Computer Equipment / Computer Hardware

Intel MS-6112 manual Chapter, Hardware Installation, The installation is now complete, PC-3745

Models: MS-6112

1 68

Page 18

CHAPTER 2	HARDWARE INSTALLATION

PC-3745

Step 7: Lock the Processor Locks and Heat Sink Support Locks

Secure the CPU by pushing out the Processor Locks. Close the Heat Sink Support Locks.

The installation is now complete.

2-13

Page 18

Image 18

Intel MS-6112 manual Chapter, Hardware Installation, The installation is now complete, PC-3745

Contents

Chapter INTRODUCTION Chip Set 1.1 Mainboard FeaturesSwitching Voltage Regulator Clock GeneratorOn-BoardIDE BIOSKeyboard Connector On-BoardPeripheralsINTRODUCTION DimensionCHAPTER lATX Form Factor 30cmL x 23cmW x 4 layers PCBBIOS 1.2 Mainboard LayoutMS-6112 SLOTChapter HARDWARE INSTALLATION 2.1 Central Processing Unit CPU2.1-1CPU Installation Procedures Required ThingsHSSBASE RM HSSPIN RMAMHSSTOP Page CHAPTER CHAPTER CHAPTER HARDWARE INSTALLATIONStep 6 Install the Processor Step 7 Lock the Processor LocksThe installation is now complete HARDWARE INSTALLATIONStep 8 Install the Heat Sink Support Top Bar CHAPTERCHAPTER CHAPTER HARDWARE INSTALLATIONStep 3 Install the Heat Sink Support Base Retention Mechanism Notch HoleCHAPTER HARDWARE INSTALLATIONStep 4 Install the Heat Sink Support Intel Boxed PentiumTM Processor Heat Sink SupportCHAPTER CHAPTER HARDWARE INSTALLATIONThe installation is now complete PC-3745200MHz 2.1-2CPU Speed Setting SW1Type 233MHzCHAPTER 2.1-3CPU Clock Generator Setting J10/J9HARDWARE INSTALLATION These jumper is used to set the CPU Clock2.1-4CPU Fan Power Connectors JFAN/CFAN1/SFAN1 PSFAN1+12V PWD VCC Voltage Setting2.2 Flash ROM Programming Voltage JMODE1 +12V2.3 External Battery Connector JBAT1 2.4 Memory Installation 2.4-1Memory Bank ConfigurationA. How to install a DIMM Module 2.4-2Memory Installation ProceduresSingle Sided DIMM Double Sided DIMM 2-20CHAPTER 2.4-1Memory Population RulesHARDWARE INSTALLATION 1.Supports EDO and SDRAMTable 2.4-1EDO DRAM Memory Addressing Table 2.4-2SDRAM Memory AddressingReset 2.5 Case Connector JFP1Power Switch2.5-1Turbo LED 2.5-2Reset Switch2.5-4Power LED 2.5-3Keylock2.6 Floppy Disk Connector FDC HARDWARE INSTALLATIONCHAPTER 2.7 Hard Disk Connectors IDE1 & IDE2 SIGNAL 2.8 Power Supply2.8-1ATX 20-pinPower Connector JPWR1 SIGNAL2.8-2Remote Power On/Off Switches JSW1/JSW2 CHAPTER 2.9 IrDA Infrared Module Connector IR1HARDWARE INSTALLATION 1 VCC NC IRRX GND IRTX2.10 Serial Port Connectors COM A & COM B PIN DEFINITIONSIGNAL SIGNAL 2.11 Parallel Port Connector LPTSIGNAL PIN DEFINITION2.12 Mouse Connector: JKBMS1 2.13 Keyboard Connector JKBMS12.14 USB Connector USB SIGNAL2-33 2.15 Power Saving LED Connector JGL1 HARDWARE INSTALLATIONCHAPTER 2.16 Special Jumpers J3/J4 HARDWARE INSTALLATIONCHAPTER Chapter AMI BIOS USER GUIDE AMI BIOS USER’S GUIDECHAPTER 3.1 Enter BIOS Setup CHAPTER 3.2 Standard CMOS Setup 3.3 Advanced CMOS Setup Try other Boot Devices Quick Boot1st Boot Device/2nd Boot Device/3rd Boot Device Floppy Access ControlFloppy Drive Swap Boot up Num LockPassword Check Floppy Drive SeekParity Check Boot to OS/2System BIOS Cacheable Internal Cache/External CacheCHAPTER 3.4 Advanced Chipset Setup SDRAM RAS to CAS Delay Auto Configure EDO DRAM TimingEDO RAS to CAS Delay EDO DRAM Speed nsDRAM Integrity Mode SDRAM CAS LatencySDRAM RAS Precharge Time VGA Frame Buffer USWCFixed Memory Hole PCI Frame Buffer USWCDRAM Refresh Queue CPU To PCI IDE PostingUSB Passive Release PIIX4 Delayed TransactionAGP Aperture Size PIIX4 Passive ReleaseAMI BIOS USER’S GUIDE USB FunctionUSB Keyboard Legacy Support CHAPTER3.5 Power Management Setup Video Power Down Mode Power Management/APMGreen PC Monitor Power State Hard Disk Power Down ModeThrottle Slow Clock Ratio Standby Time OutSuspend Time Out Modem Use IO PortPower Button Function RTC Alarm Resume From Soft-OffRing Resume from Soft-Off 3.6 PCI/Plug and Play Setup PCI VGA Palette Snoop PCI Latency Timer PCI ClocksPlug and Play Aware O/S Allocate IRQ to PCI VGAOffboard PCI IDE Primary IRQ PCI IDE BusMasterOffboard PCI IDE Card Offboard PCI IDE Secondary IRQDMA Channel 0/1/3/5/6/7 IRQ3/IRQ4/IRQ5/RQ7/IRQ9/IRQ10/IRQ11/IRQ14/IRQ15Reserved Memory Size/Reserved Memory Address 3.7 Peripheral Setup Description of the item on screen follows Onboard FDCOnboard Serial Port A/Onboard Serial Port B If the ISA add-oncard hasIR IRQ Select IR Port SupportIR Base Address Select IR DMA SelectParallel Port IRQ EPP VersionParallel Port Mode Parallel Port DMA Channel3.8 Hardware Monitor Setup AMI BIOS USER’S GUIDECHAPTER