Manuals / Invacare / Lawn and Garden / Hot Tub

Invacare 3650 NOTE For this procedure, refer to .4 on page, NOTE Use 15 AMP GFCI breaker only

Models: 3650

1 36

Download 36 pages 42.37 Kb

Page 18

NOTE: For this procedure, refer to FIGURE 2.4 on page 19.

SECTION 2—PARTS AND INSTALLATION

WARNING

All electrical conduit, fittings and wire to unit are to be supplied and installed by a professional electrician in accordance with the National electrical code as a minimum requirement, including the supply and installation of a Ground Fault Circuit Interrupter (GFCI).

For Canadian installation, ground fault interrupter and a 30-minute maximum timer MUST be installed in the electrical circuit. (Parts not supplied by ICCG). The unit must be operated through the circuit. The 30-minute timer must be located in a position where a person in the unit cannot reach the timer.

NOTE: For this procedure, refer to FIGURE 2.4 on page 19.

NOTE: Use 15 AMP GFCI breaker only.

1.Ensure a 15 AMP GFCI breaker is installed to protect the unit.

2.Connect the green terminal to the grounding terminal of the electric service supply panel using a continuous green insulated copper wire equivalent in size to the circuit conductors supplying this equipment, but no smaller than No. 8AWG (3.3 mm).

NOTE: The green terminal may be a wire connector marked “G”, “GR”, “Ground” or “Grounding”.

3.Use the pressure wire connector on the exterior of the terminal box to connect the No. 8AWG (8.4 mm) solid copper bonding conductor between the unit and all other electrical equipment and exposed metal in the vicinity, to comply with local requirements.

4.Use a pneumatic air switch with the push button located on the tub deck for On/Off switching.

5.Install a 115V electrical hook‐up per local electrical codes through a dedicated GFCI circuit (Detail “A”).

6.Remove service access panel by removing screws, in order to access pump electric connections.

7.Route electrical line through electrical line routing hole in back panel.

8.Remove the motor cover (Detail “C”).

9.Connect ground, neutral and hot wires from wall directly to motor through the electrical line routing hole in the back panel (Detail “D”).

Side Entry Whirlpool Tub

18

Part No 1118387

Image 18

Invacare 3650 manual NOTE For this procedure, refer to .4 on page, NOTE Use 15 AMP GFCI breaker only

Contents

Model 3600 & Model 3600XL Model Owner’s Operator and Maintenance ManualSide Entry Whirlpool Tub DEALER This manual MUST be given to the user of the tubACCESSORIES WARNING Customer Service ‐ 1‐800‐668‐2337 Technical Support ‐ 1‐800‐668‐2337For further information on this product, please call the following FEATURES TABLE OF CONTENTSTABLE OF CONTENTS SECTION 2-PARTS AND INSTALLATIONRemoving Soap Film and Hard Water Deposits TABLE OF CONTENTSTABLE OF CONTENTS Removing Calcium Deposits, Scale and Lime Build-upSPECIAL NOTES Disinfecting Cabinet Door LABEL LOCATIONLABEL LOCATION Labels located inside the DisinfectingMODEL TYPICAL PRODUCT PARAMETERSTYPICAL PRODUCT PARAMETERS 3650FEATURES FEATURESModels 3600 and 3600XL Aerator Valve ModelFEATURES Control Panel See AboveSECTION 1-GENERAL GUIDELINES SAVE THESE INSTRUCTIONS Important Safety InstructionsInstallation DANGERDANGER ElectricalPlumbing GroundingMaintenance and Inspection DANGER DisinfectingDANGER OperationNOTE For this procedure, refer to FIGURE 2.1 on page SECTION 2-PARTS AND INSTALLATIONAbout Installation Parts InformationService Access Panel FIGURE 2.1 Preparing the Work AreaSECTION 2-PARTS AND INSTALLATION Service Access PanelNOTE For this procedure, refer to FIGURE Securing TubElectrical and Plumbing Hook-up Locations on the Tub Electrical InstallationNOTE For this procedure, refer to FIGURE 2.3 on page DANGERNOTE For this procedure, refer to FIGURE 2.4 on page NOTE Use 15 AMP GFCI breaker only1. Ensure a 15 AMP GFCI breaker is installed to protect the unit Service FIGURE 2.4 Electrical InstallationSECTION 2-PARTS AND INSTALLATION Air Switch Line Motor CoverPlumbing Installation NOTE For this procedure, refer to FIGURE 2.5 on pageDANGER Post Installation Checklist SECTION 3-OPERATING INSTRUCTIONS OverviewDisinfecting the Tub Using the Closed Loop System FIGURE 3.1 Disinfecting the Tub Using the Closed Loop SystemSECTION 3-OPERATING INSTRUCTIONS Opening the Tub Door NOTE For this procedure, refer to FIGURE 3.2 on pageOpening/Closing the Tub Door Closing the Tub DoorWater Temperature Setting Tub OperationNOTE For this procedure, refer to FIGURE Operating Shower/Massage Wand NOTE Refer to following chart for shower head adjustment settingsNOTE For this procedure, refer to FIGURE 3.5 on page Filling TubNOTE For this procedure, refer to FIGURE 3.6 on page HydromassageInitially SECTION 4-SAFETY INSPECTION/ TROUBLESHOOTINGSafety Inspection Checklists Before Each UseCleaning Your Tub CleaningCleaning the Door Seal Gasket Removing Soap Film and Hard Water DepositsHeavy Duty Cleaning Procedure SECTION 4-SAFETY INSPECTION/TROUBLESHOOTINGNOTE Equipment needed Bucket or Pail, at least 1 Gallon NOTE For this procedure, refer to FIGURE 4.1 on pageCalibrating the Disinfectant Flow Meter Graduated plastic bottle, at least 16 ounces Felt Tip PenNOTE Liquid will be heard filling the interior plumbing of the tub 12. Close the whirlpool inlet by pulling the inlet plug outDisinfectant Valve Injector Screw TroubleshootingBurp Fitting Burp Fitting Disinfectant Cabinet DoorTYPE OF MAINTENANCE PERFORMED Maintenance RecordMAINTENANCE PERSON DATESide Entry Whirlpool Tub LIMITED WARRANTY Canada