Tool QTY | Invacare Pronto M51 Base specs

SECTION 9—BATTERIES

Removing/Installing Batteries from/into Battery Tray

WARNING

ALWAYS use the battery handle when lifting the battery. It is the most convenient method and assures that the battery acid will not spill. It also helps to prolong the life of the battery.

DO NOT tip the batteries. Keep the batteries in an upright position.

NOTE: For this procedure, refer to FIGURE 9.2 on page 54.

NOTE: If there is battery acid in the bottom of the battery tray or on the sides of the battery, apply baking soda to these areas to neutralize the battery acid. Before reinstalling the existing or new battery, clean the baking soda from the battery tray or battery being sure to avoid contact with skin and eyes. Determine source of contamination. NEVER install/reinstall a battery with a cracked or otherwise damaged case.

NOTE: Have the following tools available:

TOOL	QTY	COMMENTS

7/16-INCH (6PT) BOX WRENCH	1	Not Supplied

DIAGONAL CUTTERS	1	Not Supplied

Removing

1.Place the wheelchair in a well ventilated area where work can be performed without risking damage to carpeting or floor covering.

2.Verify the joystick On/Off switch is in the Off position and disconnect joystick cable (not shown). Refer to Disconnecting/Connecting the Joystick on page 121.

3.Perform one of the following:

•Tilt the seat assembly to the up position. Refer to Tilting the Seat Assembly (Formula CG Only) on page 41.

•Remove the seat assembly from the wheelchair. Refer to Removing/Installing the Seat Assembly on page 43.

4.Remove the battery shroud. Refer to Removing/Installing the Battery Shroud on page 47.

5.Disconnect the front battery from the controller (BLACK connector).

6.Disconnect the rear battery from the front battery (RED and BLACK connectors).

7.Lift rear and front battery out of the battery tray using the battery handles.

Installing

1.Verify the joystick On/Off switch is in the Off position and disconnect joystick cable. Refer to Disconnecting/Connecting the Joystick on page 121.

Part No. 1148076

53

Pronto® M51™ Base with SureStep®

Image 53

Invacare Pronto M51 Base manual Removing/Installing Batteries from/into Battery Tray, Tool QTY

Contents

Pronto M51 Base with SureStep Document Reference DocumentsReference Documents Table of Contents Register Your Product Table of Contents Meaning Special NotesSpecial Notes Trro and Trbkts Warnings Typical Product Parameters Typical Product Parameters Label Location Label Location Wheelchairs With Trro Wheelchairs Without Trro General Guidelines Controller Settings/Repair or ServiceOperation Information General Guidelines Accessories Charging Batteries Batteries Weight Limitation Weight TrainingGrounding Instructions Rain Test EMI Information EMI Information EMI Information Stability and Balance SAFETY/HANDLING of WheelchairsSAFETY/HANDLING of Wheelchairs Coping With Everyday Obstacles Coping With Everyday Obstacles Lifting/Stairways Lifting/Stairways Transferring To and From Other Seats Transferring To and From Other Seats Reaching and Bending Backward Reaching, Leaning and Bending Forward Safety Inspection Checklists Safety INSPECTION/ TroubleshootingSafety INSPECTION/TROUBLESHOOTING Inspect/Adjust Initially Inspect/Adjust Weekly Troubleshooting GuideInspect/Adjust Monthly Inspect/Adjust Periodically Symptom Probable Cause Solutions General Troubleshooting Display Description Definition Information Gauge Display DiagnosticsSPJ+ w/PSS or SPJ+ w/ACC Joysticks MPJ+, PSR+, PSF+ Joysticks or Displays Service Indicator Light DiagnosticsPossible Solution BAD Joystick CAL Values DON’T Checking Battery Charge Level Wheelchair Operation Turning the Power On/OffOperating the Wheelchair Wheelchair Operation Movement Action Using the Joystick to Drive the Wheelchair Speedometer On/Off Button Speed Control Buttons Service IndicatorJoystick Charger/Programming Input Drive Select Toggle Switch MPJ+ Joystick Switches and IndicatorsSelecting the Drive Mode Information Gauge Display LCD Display Screens Speed Control Main Screen Splash Screen Wheelchair Operation Description Status Indicator Remote Stop Switch Programmable Mono Port 1/2 or External Mode SwitchRemote Mode Reset Switch Connected Devices Screen Memory Card Slot Remote On/Off SwitchMode Switch Joystick Repositioning Joystick Disconnecting Disconnecting/Connecting the JoysticksConnecting SPJ+ Joysticks Tilting the Seat Assembly Back Tilting the Seat Assembly Formula CG OnlySeat Seat Tilting the Seat Assembly Formula CG Only Tilting the Seat Assembly Forward Removing Removing/Installing the Seat AssemblyInstalling Removing/Installing the Footboard Assembly Footboard AssemblyFootboard Assembly Pinch point may occur when rotating the footboard assembly Angle Adjusting the Footboard Assembly Depth Adjusting the Footboard Assembly Angle TOP Shroud and Wheels Removing/Installing the Battery ShroudReplacing the Flat Free Tires on the Wheel Rim TOP Shroud and Wheels Removing/Installing the Battery Shroud Engaging/Disengaging Motor Release Lever Engaging/Disengaging Motor Release Lever Replacing Front/Rear Caster Assemblies Adjusting Forks Batteries Batteries Negative Using the Proper Batteries Tool QTY Removing/Installing Batteries from/into Battery Tray Removing/Installing Batteries from/into Battery Tray Connecting Battery Cables Connecting/Disconnecting Battery Cables Caps not shown on front SPJ+ w/PSS and SPJ+ w/ACC Joysticks When to Charge BatteriesDisconnecting Battery Cables MPJ+ Joystick Charging Batteries On-Board Battery Charger Battery Charger Operation ON/OFF Indicator Charger Programming Port Transport Ready Package Transport Ready Package Compliance Information SpecificationsAbout Transport Ready Packages Positioning the Wheelchair in the Vehicle Securing the Wheelchair to the Vehicle Securing the Wheelchair Securement Points Wheelchair-Anchored Belts Securing the Occupant Seating System Vehicle-Anchored Belts Positioning Belts Positioning Belts Pronto M51 Base with SureStep Pronto M51 Base with SureStep Pronto M51 Base with SureStep USA Limited Warranty