Manuals / Brands / Personal Care / Wheelchair / Invacare / Personal Care / Wheelchair

Invacare Wheelchair REPLACING BATTERY BOX RETAINING STRAP

1 48

Download 48 pages, 1.16 Mb

21

This Procedure Includes the Following:

Replacing Battery Box Retaining Strap

R

E

T

A

I

N

I

N

G

S

T

R

A

P

PROCEDURE 7RETAINING STRAP

WARNING

After ANY adjustments, repair or service and BEFORE

use, make sure all attaching hardware is tightened

securely - otherwise injury or damage may result.

NOTE: Tray shown by itself for clarity. There is no need

to remove the tray from the wheelchair if the retaining

strap is being replaced.

FIGURE 1 - REPLACING BATTERY BOX RETAINING

STRAP - RWD WHEELCHAIRS

Slot

Battery Box Tray

Retaining

Strap

Retaining

Strap Buckle

Adjustable

End

REPLACING BATTERY BOXRETAINING STRAP

WARNING

The Battery Box Retaining Strap MUST be fastened

securely and adjusted properly to hold battery

boxes in place before using the wheelchair.

RWD Wheelchairs (FIGURE 1)

1. Remove the battery boxes from the wheelchair. Refer

to INSTALLING/REMOVING BATTERY BOXES in

PROCEDURE 11 of this manual.

WARNING

The retaining strap MUST be fed through the adjust-

able end of the battery box retaining strap buckle

as shown in FIGURE 1.

2. Feed the existing battery box retaining strap through

the adjustable end of the battery box retaining strap

buckle.

3. Feed the existing battery box retaining strap through

the slot in the battery box tray.

4. Feed the new battery box retaining strap through the

inside of the slot in the battery box tray.

5. Feed the new battery box retaining strap through the

adjustable end of the battery box retaining strap buckle.

6. Reinstall the battery box. Refer to INSTALLING/RE-

MOVING BATTERY BOXES in PROCEDURE 11 of

this manual.

FWD Wheelchairs (FIGURE 2)

1. Remove the battery boxes from the wheelchair. Refer

to INSTALLING/REMOVING BATTERY BOXES in

PROCEDURE 10 of this manual.

2. Remove the two (2) hex bolts and locknut that se-

cure the existing battery tray to the tray support.

3. Remove the existing battery tray from the wheelchair.

4. Position the new battery tray on the tray support as

shown in FIGURE 2.

5. Secure the new battery tray to the tray support with

the two (2) hex bolts and locknuts. Tighten securely.

6. Reinstall the battery box. Refer to INSTALLING/

REMOVING BATTERY BOXES in PROCEDURE

10 of this manual.

FIGURE 2 - REPLACING BATTERY BOX RETAINING

STRAP - FWD WHEELCHAIRS

Battery Tray

Tray Support

Hex Bolt

Locknut

Contents

Main WARNING SPECIAL NOTES TABLE OF CONTENTS A B L E S TABLE OF CONTENTS s except where specified. wheelchair The following procedures refer to POWER 9000 and EXCEL SPECIFICATIONS SPECIFICATIONS NOTE: All specifications are approximate. EXCEL INTEGRATED SLING SEAT NOTE: 18-in. wide x 16-in. deep wheelchair with MKIV RII electronics. SPECIFICATIONS POWER 9000 NOTE: 18-inch wide x 16-inch deep wheelchair with MKIV RII electronics. PERFORMANCE GENERAL WARNINGS GENERAL WARNINGS (CONTINUED) SAFETY/HANDLING OF WHEELCHAIRS ESCALATORS? SORRY! NOTE: The front motor mounting holes are reserved for future applications. EXCEL FACTORY SETTINGS USERS' WEIGHT 200 LBS AND UNDER - USERS' WEIGHT 201 TO 250 LBS - Page Page SAFETY INSPECTION/TROUBLESHOOTING PROCEDURE 2 SAFETY INSPECTION CHECKLIST Checking Battery Charge Level TROUBLESHOOTING - MECHANICAL WARNING SAFETY INSPECTION/TROUBLESHOOTINGPROCEDURE 2 TROUBLESHOOTING - ELECTRICAL DONT DO . wheelchair CHECKING BATTERY CHARGE LEVEL SAFETY INSPECTION/TROUBLESHOOTING PROCEDURE 2 FRONT RIGGINGSPROCEDURE 3 INSTALLING/REMOVING FOOTRESTS (FIGURE 1) ADJUSTING FOOTREST HEIGHT INSTALLING/REMOVING ELEVATING LEGRESTS (FIGURE 5) FRONT RIGGINGS PROCEDURE 3 REPLACING HEEL LOOPS (FIGURE 4) RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS (FIGURE 6) ARMSPROCEDURE 4 ADJUSTING ARMREST HEIGHT, REMOVING OR REPLACING ARMRESTS (FIGURE 1) ADJUSTING CAPTAIN'S SEAT ARMRESTS (FIGURE 2) REPLACING SEAT POSITIONING STRAP (FIGURE 2) U Y PROCEDURE 5UPHOLSTERY/POSITIONING STRAP REPLACING SEAT UPHOLSTERY (FIGURE 1) PREPARING MKIV JOYSTICK FOR USE (FIGURE 1) REPOSITIONING MKIV JOYSTICK (FIGURE 2) REPLACING BATTERY BOX RETAINING STRAP ADJUSTING FORKS (FIGURE 1) INSTALLING/REMOVING BATTERIES INTO/FROM BATTERY BOXES (FIGURE 1) PROCEDURE 9 BATTERIES CONNECTING BATTERY CABLES DIRECT MOUNT METHOD (FIGURE 2 AND 3). NOTE: It will be necessary to trim excess tie-wrap in order to install the battery box top(s). Page Battery Cable Battery Clamp Cover NEGATIVE (-) Battery Terminal/Post and Battery Clamp POSITIVE (+) Battery Terminal/Post (Note position of battery clamp) PROCEDURE 9 BATTERIES Page TRANSPORTING EXCEL Push Brackets Crossbraces ADJUSTING/REPLACING TELESCOPING FRONT RIGGING SUPPORT (FIGURE 3) Locknuts H-Block Socket Bolt Wheelchair Frame ADJUSTING FLIP-UP REMOVABLE FOOTBOARD (FIGURE 4) ADJUSTING CAPTAIN'S SEAT (FIGURE 5) Release Handle Knob - High Back Captain's Seats Only Flip Up Footboard REMOVING/INSTALLING CAPTAIN'S SEAT (FIGURE 6) DISCONNECTING/CONNECTING LIMIT SWITCH (FIGURE 7) REMOVING/INSTALLING SHROUDS (FIGURE 8) REPOSITIONING BATTERY CHARGER CONNECTOR (FIGURE 9) Spiral Wire Cover Battery Charger Cable NOTE: Accurate readings are displayed when in neutral. Locknut Hex Bolt CHARGING BATTERIES (FIGURE 11) REPLACING BATTERIES BATTERY TRAY INSTALLING/REMOVING BATTERY BOXES (FIGURE 12) ENGAGING/DISENGAGING CLUTCHES (FIGURES 15 AND 16) TRANSPORTING POWER 9000 (FIGURE 1) WHEN TO CHARGE BATTERIES (FIGURE 2) PROCEDURE 11RWD WHEELCHAIRS CHARGING BATTERIES (FIGURE 3) REPLACING BATTERIES INSTALLING/REMOVING BATTERY BOXES (FIGURE 4) BATTERY TRAY (FIGURE 5) ENGAGING/DISENGAGING CLUTCHES (FIGURES 6 AND 7) USING/INSTALLING/ADJUSTING WHEEL LOCKS* INSTALLING/REMOVING ANTI- TIPPERS (FIGURE 10) INSTALLING OPTIONAL CLUTCH EXTENSION HANDLES (FIGURE 11) Page Page LIMITED WARRANTY WARRANTY