Manuals / Brands / Personal Care / Wheelchair / Invacare / Personal Care / Wheelchair

Invacare Wheelchair INSTALLING OPTIONAL CLUTCH EXTENSION HANDLES (FIGURE 11)

1 48

Download 48 pages, 1.16 Mb

INSTALLING OPTIONAL CLUTCHEXTENSION HANDLES (FIGURE 11)

1. Turn the power to the wheelchair to the OFF position.

2. Position the clutch extension handle by the clutch

handle on the motor as shown in FIGURE 11.

NOTE: If the clutch handle on the motor is equipped with

a rubber tip, remove the rubber tip before installing the

clutch extension handle.

3. Slide clutch extension handle onto motor clutch handle.

NOTE: If necessary, lightly tap the clutch extension handle

onto the clutch handle with a plastic mallet. Make sure the

vertical portions of both handles are in line.

4. Securely tighten set screw on clutch extension handle.

5. Repeat STEPS 2-4 for opposite side of wheelchair.

Clutch

Extension

Handle

Clutch

Handle

Motor

Remove

Rubber Tip

if Equipped

NOTE: Make sure vertical

portions of both handles are

in line.

Set Screw

FIGURE 11 - INSTALLING OPTIONAL CLUTCH

EXTENSION HANDLES

PROCEDURE 11 RWD WHEELCHAIRS

Contents

Main WARNING SPECIAL NOTES TABLE OF CONTENTS A B L E S TABLE OF CONTENTS s except where specified. wheelchair The following procedures refer to POWER 9000 and EXCEL SPECIFICATIONS SPECIFICATIONS NOTE: All specifications are approximate. EXCEL INTEGRATED SLING SEAT NOTE: 18-in. wide x 16-in. deep wheelchair with MKIV RII electronics. SPECIFICATIONS POWER 9000 NOTE: 18-inch wide x 16-inch deep wheelchair with MKIV RII electronics. PERFORMANCE GENERAL WARNINGS GENERAL WARNINGS (CONTINUED) SAFETY/HANDLING OF WHEELCHAIRS ESCALATORS? SORRY! NOTE: The front motor mounting holes are reserved for future applications. EXCEL FACTORY SETTINGS USERS' WEIGHT 200 LBS AND UNDER - USERS' WEIGHT 201 TO 250 LBS - Page Page SAFETY INSPECTION/TROUBLESHOOTING PROCEDURE 2 SAFETY INSPECTION CHECKLIST Checking Battery Charge Level TROUBLESHOOTING - MECHANICAL WARNING SAFETY INSPECTION/TROUBLESHOOTINGPROCEDURE 2 TROUBLESHOOTING - ELECTRICAL DONT DO . wheelchair CHECKING BATTERY CHARGE LEVEL SAFETY INSPECTION/TROUBLESHOOTING PROCEDURE 2 FRONT RIGGINGSPROCEDURE 3 INSTALLING/REMOVING FOOTRESTS (FIGURE 1) ADJUSTING FOOTREST HEIGHT INSTALLING/REMOVING ELEVATING LEGRESTS (FIGURE 5) FRONT RIGGINGS PROCEDURE 3 REPLACING HEEL LOOPS (FIGURE 4) RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS (FIGURE 6) ARMSPROCEDURE 4 ADJUSTING ARMREST HEIGHT, REMOVING OR REPLACING ARMRESTS (FIGURE 1) ADJUSTING CAPTAIN'S SEAT ARMRESTS (FIGURE 2) REPLACING SEAT POSITIONING STRAP (FIGURE 2) U Y PROCEDURE 5UPHOLSTERY/POSITIONING STRAP REPLACING SEAT UPHOLSTERY (FIGURE 1) PREPARING MKIV JOYSTICK FOR USE (FIGURE 1) REPOSITIONING MKIV JOYSTICK (FIGURE 2) REPLACING BATTERY BOX RETAINING STRAP ADJUSTING FORKS (FIGURE 1) INSTALLING/REMOVING BATTERIES INTO/FROM BATTERY BOXES (FIGURE 1) PROCEDURE 9 BATTERIES CONNECTING BATTERY CABLES DIRECT MOUNT METHOD (FIGURE 2 AND 3). NOTE: It will be necessary to trim excess tie-wrap in order to install the battery box top(s). Page Battery Cable Battery Clamp Cover NEGATIVE (-) Battery Terminal/Post and Battery Clamp POSITIVE (+) Battery Terminal/Post (Note position of battery clamp) PROCEDURE 9 BATTERIES Page TRANSPORTING EXCEL Push Brackets Crossbraces ADJUSTING/REPLACING TELESCOPING FRONT RIGGING SUPPORT (FIGURE 3) Locknuts H-Block Socket Bolt Wheelchair Frame ADJUSTING FLIP-UP REMOVABLE FOOTBOARD (FIGURE 4) ADJUSTING CAPTAIN'S SEAT (FIGURE 5) Release Handle Knob - High Back Captain's Seats Only Flip Up Footboard REMOVING/INSTALLING CAPTAIN'S SEAT (FIGURE 6) DISCONNECTING/CONNECTING LIMIT SWITCH (FIGURE 7) REMOVING/INSTALLING SHROUDS (FIGURE 8) REPOSITIONING BATTERY CHARGER CONNECTOR (FIGURE 9) Spiral Wire Cover Battery Charger Cable NOTE: Accurate readings are displayed when in neutral. Locknut Hex Bolt CHARGING BATTERIES (FIGURE 11) REPLACING BATTERIES BATTERY TRAY INSTALLING/REMOVING BATTERY BOXES (FIGURE 12) ENGAGING/DISENGAGING CLUTCHES (FIGURES 15 AND 16) TRANSPORTING POWER 9000 (FIGURE 1) WHEN TO CHARGE BATTERIES (FIGURE 2) PROCEDURE 11RWD WHEELCHAIRS CHARGING BATTERIES (FIGURE 3) REPLACING BATTERIES INSTALLING/REMOVING BATTERY BOXES (FIGURE 4) BATTERY TRAY (FIGURE 5) ENGAGING/DISENGAGING CLUTCHES (FIGURES 6 AND 7) USING/INSTALLING/ADJUSTING WHEEL LOCKS* INSTALLING/REMOVING ANTI- TIPPERS (FIGURE 10) INSTALLING OPTIONAL CLUTCH EXTENSION HANDLES (FIGURE 11) Page Page LIMITED WARRANTY WARRANTY