Manuals / Brands / Personal Care / Wheelchair / Invacare / Personal Care / Wheelchair

Invacare Wheelchair REMOVING/INSTALLING SHROUDS (FIGURE 8)

1 48

Download 48 pages, 1.16 Mb

32

REMOVING/INSTALLING SHROUDS(FIGURE 8)

Removing Front Shroud

1. Unclip the retaining strap securing the front shroud

and battery box to the wheelchair.

2. Feed the retaining strap through the front shroud.

3. Remove the front shroud from the wheelchair.

Installing Front Shroud

1. Feed the retaining strap through the front shroud as

shown in FIGURE 8.

2. Position the bottom of the front shroud between the

battery box and the battery tray.

3. Clip the retaining strap together.

Removing Rear Shroud

1. Unclip the retaining strap securing the rear shroud

and battery box to the wheelchair.

2. Feed the retaining strap through the rear shroud.

3. Remove the rear shroud from the wheelchair.

Installing Rear Shroud

1. Feed the retaining strap through the front shroud as

shown in FIGURE 8.

2. Clip the retaining strap together.

FIGURE 8 - REMOVING/INSTALLING SHROUDS - FWD WHEELCHAIRS

Front Shroud

Phillips Screws

Washers

Rear Shroud

Side Shroud

Phillips Bolts

Locknut

Wheelchair

Frame

Filler

Retaining Strap

Retaining Strap

Battery Box Battery Tray

Phillips Screws

Battery Charger

Cover

3. Press down on the rear shroud until the two (2) clips

secure the rear shroud to the two (2) side shrouds.

Removing Side Shrouds and Fillers

1. Remove the front shroud from the wheelchair. Refer

to REMOVING/INSTALLING FRONT SHROUD in

this procedure of the manual.

2. Remove the rear shroud from the wheelchair. Refer

to REMOVING/INSTALLING REAR SHROUD in this

procedure of the manual.

3. Perform one (1) of the following:

A. INTEGRATED SLING SEAT MODELS - Fold

the wheelchair. Refer to TRANSPORTING EX-

CEL in this procedure of the manual.

B. CAPTAIN'S SEAT MODELS - Remove the

Captain's Seat from the wheelchair. Refer to

REMOVING/INSTALLING CAPTAIN'S SEAT in

this procedure of the manual.

4. Remove the phillips screws, bolts, washers and lock-

nuts that secure side shroud and filler to the wheel-

chair frame. Refer to FIGURE 8 for phillips screw

and washer locations.

5. Remove the side shroud and filler from the wheelchair.

6. Repeat STEPS 4-5 for the opposite side of the wheel-

chair, if necessary.

PROCEDURE 10 FWD WHEELCHAIRS

F

W

D

W

H

E

E

L

C

H

A

I

R

S

Contents

Main WARNING SPECIAL NOTES TABLE OF CONTENTS A B L E S TABLE OF CONTENTS s except where specified. wheelchair The following procedures refer to POWER 9000 and EXCEL SPECIFICATIONS SPECIFICATIONS NOTE: All specifications are approximate. EXCEL INTEGRATED SLING SEAT NOTE: 18-in. wide x 16-in. deep wheelchair with MKIV RII electronics. SPECIFICATIONS POWER 9000 NOTE: 18-inch wide x 16-inch deep wheelchair with MKIV RII electronics. PERFORMANCE GENERAL WARNINGS GENERAL WARNINGS (CONTINUED) SAFETY/HANDLING OF WHEELCHAIRS ESCALATORS? SORRY! NOTE: The front motor mounting holes are reserved for future applications. EXCEL FACTORY SETTINGS USERS' WEIGHT 200 LBS AND UNDER - USERS' WEIGHT 201 TO 250 LBS - Page Page SAFETY INSPECTION/TROUBLESHOOTING PROCEDURE 2 SAFETY INSPECTION CHECKLIST Checking Battery Charge Level TROUBLESHOOTING - MECHANICAL WARNING SAFETY INSPECTION/TROUBLESHOOTINGPROCEDURE 2 TROUBLESHOOTING - ELECTRICAL DONT DO . wheelchair CHECKING BATTERY CHARGE LEVEL SAFETY INSPECTION/TROUBLESHOOTING PROCEDURE 2 FRONT RIGGINGSPROCEDURE 3 INSTALLING/REMOVING FOOTRESTS (FIGURE 1) ADJUSTING FOOTREST HEIGHT INSTALLING/REMOVING ELEVATING LEGRESTS (FIGURE 5) FRONT RIGGINGS PROCEDURE 3 REPLACING HEEL LOOPS (FIGURE 4) RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS (FIGURE 6) ARMSPROCEDURE 4 ADJUSTING ARMREST HEIGHT, REMOVING OR REPLACING ARMRESTS (FIGURE 1) ADJUSTING CAPTAIN'S SEAT ARMRESTS (FIGURE 2) REPLACING SEAT POSITIONING STRAP (FIGURE 2) U Y PROCEDURE 5UPHOLSTERY/POSITIONING STRAP REPLACING SEAT UPHOLSTERY (FIGURE 1) PREPARING MKIV JOYSTICK FOR USE (FIGURE 1) REPOSITIONING MKIV JOYSTICK (FIGURE 2) REPLACING BATTERY BOX RETAINING STRAP ADJUSTING FORKS (FIGURE 1) INSTALLING/REMOVING BATTERIES INTO/FROM BATTERY BOXES (FIGURE 1) PROCEDURE 9 BATTERIES CONNECTING BATTERY CABLES DIRECT MOUNT METHOD (FIGURE 2 AND 3). NOTE: It will be necessary to trim excess tie-wrap in order to install the battery box top(s). Page Battery Cable Battery Clamp Cover NEGATIVE (-) Battery Terminal/Post and Battery Clamp POSITIVE (+) Battery Terminal/Post (Note position of battery clamp) PROCEDURE 9 BATTERIES Page TRANSPORTING EXCEL Push Brackets Crossbraces ADJUSTING/REPLACING TELESCOPING FRONT RIGGING SUPPORT (FIGURE 3) Locknuts H-Block Socket Bolt Wheelchair Frame ADJUSTING FLIP-UP REMOVABLE FOOTBOARD (FIGURE 4) ADJUSTING CAPTAIN'S SEAT (FIGURE 5) Release Handle Knob - High Back Captain's Seats Only Flip Up Footboard REMOVING/INSTALLING CAPTAIN'S SEAT (FIGURE 6) DISCONNECTING/CONNECTING LIMIT SWITCH (FIGURE 7) REMOVING/INSTALLING SHROUDS (FIGURE 8) REPOSITIONING BATTERY CHARGER CONNECTOR (FIGURE 9) Spiral Wire Cover Battery Charger Cable NOTE: Accurate readings are displayed when in neutral. Locknut Hex Bolt CHARGING BATTERIES (FIGURE 11) REPLACING BATTERIES BATTERY TRAY INSTALLING/REMOVING BATTERY BOXES (FIGURE 12) ENGAGING/DISENGAGING CLUTCHES (FIGURES 15 AND 16) TRANSPORTING POWER 9000 (FIGURE 1) WHEN TO CHARGE BATTERIES (FIGURE 2) PROCEDURE 11RWD WHEELCHAIRS CHARGING BATTERIES (FIGURE 3) REPLACING BATTERIES INSTALLING/REMOVING BATTERY BOXES (FIGURE 4) BATTERY TRAY (FIGURE 5) ENGAGING/DISENGAGING CLUTCHES (FIGURES 6 AND 7) USING/INSTALLING/ADJUSTING WHEEL LOCKS* INSTALLING/REMOVING ANTI- TIPPERS (FIGURE 10) INSTALLING OPTIONAL CLUTCH EXTENSION HANDLES (FIGURE 11) Page Page LIMITED WARRANTY WARRANTY