Manuals / Brands / Personal Care / Wheelchair / Invacare / Personal Care / Wheelchair

Invacare Wheelchair TRANSPORTING POWER 9000 (FIGURE 1)

1 48

Download 48 pages, 1.16 Mb

38

This Procedure Includes the Following:

Transporting Power 9000

When to Charge Batteries

Charging Batteries

Replacing Batteries

Installing/Removing Battery Boxes

Battery Tray

Engaging/Disengaging Clutches

Using/Installing/Adjusting Wheel Locks

Installing/Removing Anti-Tippers

Installing Optional Clutch Extension Handles

Refer to INSTALLING/RE-

MOVING ANTI-TIPPERS in

this procedure of the manual.

FIGURE 1 - TRANSPORTING POWER 9000

Refer to INSTALLING/REMOVING

FOOTRESTS or INSTALLING/RE-

MOVING ELEVATING LEGRESTS

in PROCEDURE 3 of this manual.

TRANSPORTING POWER 9000(FIGURE 1)

WARNING

The weight of the wheelchair without the user and

batteries is approximately 82 lbs. Use proper liftng

techniques (lift with your legs) to avoid injury. Ex-

treme caution is advised when it is necessary to

move an UNOCCUPIED power wheelchair. In-

vacare recommends using two (2) assistants and

making thorough preparations. Make sure to use

ONLY secure, non-detachable parts for hand-

hold supports.

Unfolding/Folding the Wheelchair

WARNING

Keep hands and fingers clear of moving parts to

avoid injury.

UNFOLDING.

1. Push down on the seat rails until the seat rails are

positioned in the seat guides.

2. Assemble the wheelchair. Refer to FIGURE 1.

FOLDING.

1. Remove the batteries and footrests/legrests from the

wheelchair. Refer to FIGURE 1.

2. Remove the battery tray from the wheelchair. Refer

to FIGURE 1.

3. Lift up on the seat rails of the wheelchair.

Refer to INSTALLING/REMOV-

ING BATTERY BOXES and

BATTERY TRAY in this proce-

dure of the manual.

WARNING

After ANY adjustments, repair or service and BE-

FORE use, make sure all attaching hardware is

tightened securely - otherwise injury or damage

may result.

PROCEDURE 11 RWD WHEELCHAIRS

R

W

D

W

H

E

E

L

C

H

A

I

R

S

Contents

Main WARNING SPECIAL NOTES TABLE OF CONTENTS A B L E S TABLE OF CONTENTS s except where specified. wheelchair The following procedures refer to POWER 9000 and EXCEL SPECIFICATIONS SPECIFICATIONS NOTE: All specifications are approximate. EXCEL INTEGRATED SLING SEAT NOTE: 18-in. wide x 16-in. deep wheelchair with MKIV RII electronics. SPECIFICATIONS POWER 9000 NOTE: 18-inch wide x 16-inch deep wheelchair with MKIV RII electronics. PERFORMANCE GENERAL WARNINGS GENERAL WARNINGS (CONTINUED) SAFETY/HANDLING OF WHEELCHAIRS ESCALATORS? SORRY! NOTE: The front motor mounting holes are reserved for future applications. EXCEL FACTORY SETTINGS USERS' WEIGHT 200 LBS AND UNDER - USERS' WEIGHT 201 TO 250 LBS - Page Page SAFETY INSPECTION/TROUBLESHOOTING PROCEDURE 2 SAFETY INSPECTION CHECKLIST Checking Battery Charge Level TROUBLESHOOTING - MECHANICAL WARNING SAFETY INSPECTION/TROUBLESHOOTINGPROCEDURE 2 TROUBLESHOOTING - ELECTRICAL DONT DO . wheelchair CHECKING BATTERY CHARGE LEVEL SAFETY INSPECTION/TROUBLESHOOTING PROCEDURE 2 FRONT RIGGINGSPROCEDURE 3 INSTALLING/REMOVING FOOTRESTS (FIGURE 1) ADJUSTING FOOTREST HEIGHT INSTALLING/REMOVING ELEVATING LEGRESTS (FIGURE 5) FRONT RIGGINGS PROCEDURE 3 REPLACING HEEL LOOPS (FIGURE 4) RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS (FIGURE 6) ARMSPROCEDURE 4 ADJUSTING ARMREST HEIGHT, REMOVING OR REPLACING ARMRESTS (FIGURE 1) ADJUSTING CAPTAIN'S SEAT ARMRESTS (FIGURE 2) REPLACING SEAT POSITIONING STRAP (FIGURE 2) U Y PROCEDURE 5UPHOLSTERY/POSITIONING STRAP REPLACING SEAT UPHOLSTERY (FIGURE 1) PREPARING MKIV JOYSTICK FOR USE (FIGURE 1) REPOSITIONING MKIV JOYSTICK (FIGURE 2) REPLACING BATTERY BOX RETAINING STRAP ADJUSTING FORKS (FIGURE 1) INSTALLING/REMOVING BATTERIES INTO/FROM BATTERY BOXES (FIGURE 1) PROCEDURE 9 BATTERIES CONNECTING BATTERY CABLES DIRECT MOUNT METHOD (FIGURE 2 AND 3). NOTE: It will be necessary to trim excess tie-wrap in order to install the battery box top(s). Page Battery Cable Battery Clamp Cover NEGATIVE (-) Battery Terminal/Post and Battery Clamp POSITIVE (+) Battery Terminal/Post (Note position of battery clamp) PROCEDURE 9 BATTERIES Page TRANSPORTING EXCEL Push Brackets Crossbraces ADJUSTING/REPLACING TELESCOPING FRONT RIGGING SUPPORT (FIGURE 3) Locknuts H-Block Socket Bolt Wheelchair Frame ADJUSTING FLIP-UP REMOVABLE FOOTBOARD (FIGURE 4) ADJUSTING CAPTAIN'S SEAT (FIGURE 5) Release Handle Knob - High Back Captain's Seats Only Flip Up Footboard REMOVING/INSTALLING CAPTAIN'S SEAT (FIGURE 6) DISCONNECTING/CONNECTING LIMIT SWITCH (FIGURE 7) REMOVING/INSTALLING SHROUDS (FIGURE 8) REPOSITIONING BATTERY CHARGER CONNECTOR (FIGURE 9) Spiral Wire Cover Battery Charger Cable NOTE: Accurate readings are displayed when in neutral. Locknut Hex Bolt CHARGING BATTERIES (FIGURE 11) REPLACING BATTERIES BATTERY TRAY INSTALLING/REMOVING BATTERY BOXES (FIGURE 12) ENGAGING/DISENGAGING CLUTCHES (FIGURES 15 AND 16) TRANSPORTING POWER 9000 (FIGURE 1) WHEN TO CHARGE BATTERIES (FIGURE 2) PROCEDURE 11RWD WHEELCHAIRS CHARGING BATTERIES (FIGURE 3) REPLACING BATTERIES INSTALLING/REMOVING BATTERY BOXES (FIGURE 4) BATTERY TRAY (FIGURE 5) ENGAGING/DISENGAGING CLUTCHES (FIGURES 6 AND 7) USING/INSTALLING/ADJUSTING WHEEL LOCKS* INSTALLING/REMOVING ANTI- TIPPERS (FIGURE 10) INSTALLING OPTIONAL CLUTCH EXTENSION HANDLES (FIGURE 11) Page Page LIMITED WARRANTY WARRANTY