•Press the MAIN Selector h.
•Press the Mute Button c to store the DCR600II’s Power On command.
•Press the TV Input Selector Button o to indicate the next command is for “TV Power On.”
•Press the Mute Button c to store the TV Power On command.
•Press the VID 3 Input Selector Button n to indicate the next command is for “Cable Power On.”
•Press the Mute Button c to store the Cable Power On command.
•Press the Macro 1 Button f to com- plete the process and store the macro sequence.
After following these steps, each time you press the Macro 1 Button f, the remote will send the Power On/Off command to only those devices.
Erasing Macro Commands
To remove the commands that have been pro- grammed into one of the Macro buttons, follow these steps:
1.Press the Mute Button c and the Macro Buttons bfg that contain the commands you wish to erase.
2.Note that the Program Indicator LED will turn red.
3.Within ten seconds, press the Surround Mode Selector Button t, followed by the Macro Buttons bfg that contain the commands you wish to erase.
4.The Program Indicator LED will flash three times before it goes out.
5.When the Program Indicator LED goes out, the Macro has been erased.
Device Functions
Once the remote has been programmed for the codes of other devices, press the appropriate Input Selector dijl–oto change the remote from controlling the DCR600II and DVD600II to controlling the additional product. When you press any one of the selectors, it will briefly flash in red to indicate that you have changed the device being controlled.
44
When operating a device other than the DCR600II or DVD600II, the controls may not correspond exactly to the function printed on the remote or button. Some commands, such as the transport controls, will operate the same way for that device as they do for the DCR600II and DVD600II. Other buttons will change their function so that they correspond to a secondary label on the remote. For example, the Sleep p and Surround Mode Selector t buttons also function as the Channel Up and Channel Down buttons when operating most TV sets, VCRs or cable boxes. The Channel Up/Down indication is printed directly on the remote. For many standard CD players, cassette decks, VCRs and DVD functions, the standard function icons are printed on top of the buttons.
For some products, however, the function of a particular button does not follow the command printed on the remote. In order to see which function a button controls, consult the Function List tables on pages 26 and 27. To use those tables, first check the type of device being con- trolled (e.g., TV, VCR). Next, look at the remote control diagram. Note that each button has a number on it.
To find out what function a particular button has for a specific device, find the button number on the Function List and then look in the column for the device you are controlling. For example, button number 7 is the Macro 2 button for the DCR600II, but it is the Repeat button for CD players, and the Favorite Channels button for cable boxes and satellite receivers. Button num- ber 32 is the Delay button for the DCR600II, but the Time button for CD players, and Preview Channel button for many TVs, cable television boxes and satellite services.
Notes on Using the Remote
With Other Devices
•Manufacturers may use different code sets for the same product category. For that reason, it is important that you check to see whether the code set you have entered operates as many controls as possible. If it appears that only a few functions operate, check to see whether another code set will work with more buttons.
•When a button is pressed on the remote, the red light under the Input Selector d h–jl–ofor the product being operated should flash briefly. If the Device Control Selector flashes for some but not all buttons for a particular product, it does NOT indicate a problem with the remote but rather that no function is programmed for the button being pushed. Consult the Function List on
pages 26 and 27. Blank squares indicate that no function is programmed for that button for the corresponding device. Consult the device‘s owner‘s manual for further information.
Volume Control Punch-Through
The remote may be programmed to operate the Volume Control sw and Mute c func- tions of either the TV or the DCR600II in conjunc- tion with any of the devices controlled by the remote. For example, since the DCR600II will likely be used as the sound system for TV viewing, you may wish to have the volume control on the DCR600II activated, although the remote is set to run the TV. To program the remote for Volume Punch-Through, follow these steps:
1.Press the Input Selector dijl– o for the source unit you wish to have asso- ciated with the volume control and the Mute Button c at the same time until the red light appears under the Input Selector di jl–oand note that the Program Indicator LED will light.
2.Press the Volume Up Button s and note that the Input Selector dijl– o will flash once.
3.Press either the MAIN Selector h or the Input Selector dijl–o, depending on which system’s volume control you wish to have attached for the punch- through mode. The Program Indicator LED will go out and the Input Selector di jl–oyou pressed in Step 1 will blink three times and then go out to confirm the data entry.
Examples:
1.To adjust the volume control for the DCR600II while the remote is set to control the DVD600II, press the DVD Selector d and the Mute Button c at the same time, then press the Volume Up Button s, then press the MAIN Selector h.
2.To have the volume control for the DCR600II activated even though the remote is set to control the TV, first press the TV Input Selector o and the Mute Button c at the same time. Next, press the Volume Up Button s, followed by the MAIN Selector h.
NOTE: Should you wish to return the remote to the original configuration after entering a Volume Punch-Through, you will need to repeat the steps shown above. However, press the same Input Selector dijl–oin Steps 1 and 3.
