JVC DLA-M2000LU manual Setting and Adjusting Other Functions Options, PC2 BNC RGB

No.51781

Menu Operations

Setting and Adjusting Other Functions (OPTIONS)

Various functions are provided as shown in the “Options 1” and “Options 2” submenus.

You can set or adjust each function, as required.

1Press the MENU button.

The main menu appears on the screen.

2Select “Options” with the cursor button 5 or ∞, and press 3 or the ENTER button.

The “Options 1” submenu appears on the screen.

Options 1

Menu display	15sec	ON
Line display	5sec	OFF
Keystone	ENTER
PC 2 (BNC)	RGB	YPBPR
Options 2	ENTER

3Select the item to be adjusted with the cursor button 5 or ∞.

4Make adjustment with the cursor 2 or 3.

•While the keystone item is selected, press the ENTER button to display the “Keystone” submenu.

•To enter the “Options 2” submenu, select “Options 2” with the cursor button 5 or ∞, and press the ENTER button.

•To return to the “Options 1” submenu from the “Options 2” submenu, select “Options 1” with the cursor button 5 or ∞, and press the ENTER button.

Keystone 123

Menu Operations

Adjustment item	Button		Adjustment content
		Sets whether to clear the menu display automatically or not.
Menu display	2 or 3	15sec* : Clears the display automatically in about 15 seconds.
		ON	: Does not automatically clear the menu display.
		Sets whether to show the line display (Y/C, VIDEO, PC1, or PC2) on top right of the
Line display	2 or 3	screen or not when the VIDEO or PC button is pressed.
		5sec*	: Shows the line display for about 5 seconds.
		OFF	: Does not show the line display.
		Press the ENTER button to enter the keystone submenu.
		In the keystone submenu, press 2 or 3 to correct trapezoidal distortion of the
		projected image. (–80 ↔ 0* ↔ +128)
Keystone	ENTER	To reset the keystone (trapezoidal distortion of the picture image) to the original
		setting (factory set value: 0), press the PRESET button when the “Keystone”
		submenu appears on the screen.
		To exit the keystone submenu, press the ESCAPE button.
		Sets the input signal source according to the device connected to the PC 2 terminals.
		However, the input will be RGB irrespective of the PC signal setting.
PC2 (BNC)	2 or 3	RGB*	: For a device with analog RGB, V, H/Cs signals
		YPBPR : For a device with component (Y, B-Y, R-Y) or DTV-format (Y, PB, PR)
			signals
		Reverses image right-to-left.
Right Left rev.	2 or 3	OFF*	: For the front method.
		ON	: For upside-down hanging from the ceiling.
		Inverses image upside-down.
Top Bottom inv.	2 or 3	OFF*	: For normal setup.
		ON	: For upside-down hanging from the ceiling.
		Sets the baud rate for transmission.
RS-232C [bps]	2 or 3	9600	: 9600 bps

Options 1

Menu display	15sec	ON
Line display	5sec	OFF
Keystone	ENTER
PC 2 (BNC)	RGB	YPBPR
Options 2	ENTER

ENTER

ENTER

ENTER

Options 2

Right Left rev.	OFF	ON
Top Bottom inv.	OFF	ON
RS-232C [bps]	9600	19200
Sleep time [min]	15 30 60	OFF
Options 1	ENTER

		19200* : 19200 bps
Sleep time [min]	2 or 3	Sets the length of sleep time which automatically brings the projector into stand-by
		state. You can select one of the sleep times: 15, 30, 60 and 0 (OFF*) minutes.
* Factory set value

5Press the ESCAPE button to return to the previous menu or press the MENU button to exit the menu mode.

Note

• Refer to “Removing the Trapezoidal Distortion of the Image” on page 34 for more details about adjusting the keystone.

DEUTSH ENGLISH

1-31

*To adjust multiple items, repeat 3 to 4.

*To reset the keystone (trapezoidal distortion of the picture image) to the original setting, press the PRESET button when the “Keystone” submenu appears on the screen.

52

CAUTION

• Correctly set the “PC2 (BNC)” according to the device connected to the PC2 terminals. However, when the PC signal is

input, RGB input is used irrespective of which setting (YPBPR) is made.

53

ESPAÑ OL ITALIANO FRANÇ AIS

DLA-M2000LU DLA-M2000LE