JVC DR-MV5SE manual Select Setting, Press SET UP to complete

DISPLAY SET OTHERS

VIDEO IN/OUT RECORDING SET

VIDEO IN/OUT RECORDING SET DISPLAY SET OTHERS

DVD SET UP FUNCTION SET UP INITIAL SET UP

DVD SET UP FUNCTION SET UP INITIAL SET UP

EDITING EN 45

L-2 Select Setting F-1 Input Setting

Set “L-2 SELECT” to the appropriate mode depending on the type of appliance connected to the unit’s [L-2 IN/DECODER] connector.

1Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting” ( pg. 44).

2Press rt to select “L-2 SELECT”, then press ENTER.

3 Press rt to select the appropriate setting, then press

ENTER.
		MONITOR TYPE				4:3LB
4 Press SET UP to complete the
		F-1 INPUT				VIDEO
		L-1 INPUT				VIDEO
setting.
		L-1 OUTPUT			SCART VIDEO
NOTES:						VIDEO/RGB
		L-2 SELECT				S-VIDEO/RGB
	SET UP		OK			SAT S-VIDEO/RGB
● If “L-2 SELECT” is set to				SELECT		WITH [CURSORS]
						DECODER
	EXIT		SELECT	THEN PRESS [ENTER]
“S-VIDEO/RGB”, it is not possible

to output colour signals correctly from the VHS deck.

●If “L-2 SELECT” is set to “DECODER”, only the DVD deck operates properly.

* The boldface settings below indicate the settings at your purchase.

8L-2 SELECT — VIDEO/RGB / S-VIDEO/RGB /

SAT VIDEO/RGB / SAT S-VIDEO/RGB / DECODER

Select “VIDEO/RGB” or “S-VIDEO/RGB” to use this unit as the recording deck with the player connected to the [L-2 IN/ DECODER] connector, or to use the satellite receiver connected to the [L-2 IN/DECODER] connector.

VIDEO/RGB: If a connected appliance’s output is compatible with regular video signals, set to “VIDEO/RGB”.

S-VIDEO/RGB: If a connected appliance’s output is compatible with Y/C signals, set to “S-VIDEO/RGB”. You can obtain high-quality picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

Select “SAT VIDEO/RGB” or “SAT S-VIDEO/RGB” to view a satellite programme with the TV set while the unit is turned off. ( pg. 76)

SAT VIDEO/RGB: If a connected satellite receiver’s output is compatible with regular video signals, set to “SAT VIDEO/RGB”.

SAT S-VIDEO/RGB: If a connected satellite receiver’s output is compatible with Y/C signals, set to “SAT S-VIDEO/RGB”. You can obtain a high-quality S-VHS picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

DECODER: To use a decoder connected to the [L-2 IN/DECODER] connector.

NOTES:

●If you have a satellite receiver or a decoder connected to the [L-2 IN/ DECODER] connector, be sure to set “L-2 SELECT” back to appropriate mode after editing.

●If you are not connecting a satellite receiver or a decoder to the [L-2 IN/DECODER] connector, leave “L-2 SELECT” set to “VIDEO/RGB”.

●When “L-2 SELECT” is set to “SAT VIDEO/RGB” and “SAT S-VIDEO/ RGB”, “SAT” appears on the TV screen or front display panel instead of “L-2”.

●If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible to set “L-2 SELECT” to “DECODER” or “SAT VIDEO/RGB”.

●If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to set “L-2 SELECT” to “DECODER” or “SAT S-VIDEO/RGB”.

●If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT” to “SAT VIDEO/RGB”, “SAT S-VIDEO/RGB” or “DECODER”, be sure to connect the [L-1 IN/OUT] connector with a TV.

Set “F-1 INPUT” to the appropriate mode depending on the connector ([VIDEO] or [S-VIDEO]) being used on the front panel.

1 Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting” ( pg. 44).

2Press rt to select “F-1 INPUT”, then press ENTER.

3 Press rt to select the appropriate setting, then press

ENTER.
		MONITOR TYPE				4:3LB
4 Press SET UP to complete the
		F-1 INPUT				VIDEO
						VIDEO
setting.		L-1 INPUT				S-VIDEO
		L-1 OUTPUT			SCART VIDEO
		L-2 SELECT			S-VIDEO/RGB
* The boldface settings below
	SET UP		OK	SELECT WITH [CURSORS]
indicate the settings at your	EXIT		SELECT	THEN PRESS [ENTER]

purchase.

8F-1 INPUT — VIDEO / S-VIDEO

VIDEO: When connecting an appliance to the [VIDEO] input connector, set to “VIDEO”.

S-VIDEO: When connecting an appliance to the [S-VIDEO] input connector, set to “S-VIDEO”.