No Operation Action Setting values: Off, On

Setting of the function for turning the unit off (standby) automatically when no operations are made for more than 4 hours.

Off: Does not turn off automatically

On: Turns off automatically

●When the function is turned On, a warning message will be displayed about 3 minutes before turning off automatically.

When you turn on the unit with the function turned On, a message notifying that the setting is turned on will be displayed for about 30 seconds.

Set-Up Menu

Function Setting

Settings for the sub menu display, color of the tally lamp, and the intensity of the button lamps.

Item

 

To do

 

Setting value

sub menu Position

Select the contents and displaying position of “sub menu.”

Lower1, Upper1, Lower2,

 

 

 

Lower1

: Displays the current setting and adjustment bar at the lower part of the screen.

Upper2

 

 

 

Upper1

: Displays the current setting and adjustment bar at the upper part of the screen.

 

 

 

 

Lower2

: Displays the current setting at the lower part of the screen.

 

 

 

 

Upper2

: Displays the current setting at the upper part of the screen.

 

 

 

 

• The adjustment bar is not displayed for some items.

 

Tally Setting

 

Set the color and mode of the tally lamp using external control.

 

 

Tally Type

 

Normal

: Light up the entire tally.

Normal, Half

 

 

 

Half

: Light up the left and right halves of the tally individually.

 

 

 

 

 

Tally Color

 

Set the tally color when “Tally Type” is set to “Normal”.

Green, Red

 

Back Tally Enable *1

Select whether to use back tally lamp.

Off, On

Dimmer

 

Select the intensity of the button lamps.

Normal, Dark

Component Phase

Deactivates the function of PHASE adjustment (Picture adjustment knob and “Picture Sub

Enable, Disable

 

 

 

Adjust” in Set-Up Menu) except when an NTSC signal comes in (☞ on page 38).

 

Remote Active On

Set the conditions for the power switch by external control (serial).

Off, On

Standby

 

Off

: Cannot power on by external control after powered OFF.

 

 

 

 

On

: Can power on by external control after powered OFF.

 

LCD Saver

 

Configure the setting for reducing damage to the LCD panel for long-time use. (☞ on page 41)

 

 

Setting

1st Start

Set the standby time. (unit: hours)

00h-24h

 

 

Work

Set the time for performing the function. (unit: hours)

01h-06h

 

 

Time

 

 

 

 

 

 

 

 

 

Contrast

Set the contrast reduction.

Normal, Save

 

 

Backlight

Reduce the backlight brightness.

Normal, Save

 

 

OSD

Set the contrast reduction of the OSD display.

Normal, Save

 

 

Contrast

 

 

 

 

 

 

 

 

 

Side Mask

Select whether to use the side mask.

Off, On

 

 

 

* The Side Mask function works no matter whether the LCD Saver is active or stopped.

 

 

 

 

 

 

reset

Restore the default settings for all the items in “LCD Saver”.

 

 

Execute

 

Execute the LCD Saver function.

 

 

Cancel

 

Stop the LCD Saver function. (“Cancel” will be grayed out during the function stop.)

 

 

Status

 

Display the LCD Saver status.

Off, Ready

 

Start After

 

Stop the LCD Saver function. (unit: hours and minutes)

**h **min

Function Key Setting

Specify the function assigned to the F1 button.

 

 

Function1

 

Specify the function assigned to the F1 button.

- - -, Aperture, I/P Mode,

 

 

 

* See pages 32 to 40 for details of the functions assigned to Function 1.

Frame, Center Marker, Level

 

 

 

 

 

Meter Display, Gamma, Color

 

 

 

 

 

Temperature, CRC Error,

 

 

 

 

 

Manual Aspect,Time Code,

 

 

 

 

 

1:1, Dynamic, Zebra Mode *1,

 

 

 

 

 

Focus Assist Mode *1

 

Function Display

Select whether to display the status of the assigned function when you press the F1 button.

Off, Mode-1, Mode-2

 

 

 

Off

: No status display. Perform the registration function.

 

 

 

 

Mode-1

: Display the status. Perform the registration function.

 

 

 

 

Mode-2

: Display the status. Do not perform the registration function.

 

 

 

 

 

Perform the registration function when the status is displayed and the button is

 

 

 

 

 

pressed again.

 

●To display the “Function Key Setting” menu, press the button when the menu is not displayed.

●About the operations of F1 button

Each time you press the button, the setting value for the assigned function changes in order. Ex: When “Color Temperature” is assigned

Each time you press the button, three setting values alternate. *1 DT-F9L5 only.

37