JVC GY-DV500 instruction manual Rear Section Contd

2. CONTROLS, INDICATORS AND CONNECTORS

2. CONTROLS, INDICATORS AND CONNECTORS

2-5 Rear Section

!1

PUSH

0

							DV CAMCORDER
							GY-DV500
				i
q				o	Y/C OUT MONITOR OUT	LINE OUT	SYNC IN TEST OUTPUT
						CH-1 CH-2	B
DV	CH-1	AUDIO IN CH-2		TALLY			VTR
EARPHONE	LINE	MIC LINE	MIC				REMOTE

2-5 Rear Section (Cont'd)

6[CH-2 AUDIO IN] CH-2 audio input connector (XLR 3-pin)

Connect the external audio equipment or microphone to this connector. Set the CH-2 AUDIO IN LINE/MIC select switch 9 according to the connected equipment.

The audio signal input through this connector is recorded on the CH-2 audio channel. To record the audio of this

connector, set the CH-2 AUDIO INPUT switch 8 on page 14 to "REAR".

7Back tally lamp

This lamp lights up when the GY-DV500 enters the record mode. It blinks during the transition to the record mode.

•Use the VCR Setup Menu item No. 082 BACK TALLY MODE to select whether or not the lamp should light and

the lighting pattern.

☞ See "BACK TALLY MODE" on page 68.

!Battery holder lock release knob

This knob is used to open the battery case cover. Press the knob to open the cover.

@[BRAKER]

The braker trips when the power consumption exceeds the capacity.

If the braker trips, confirm that the power consumption does not exceed the wattage rating. Then press BRAKER before turning the power ON again to put the camera in the operating status.

If the unit still does not work normally, please consult the person in charge of professional video equipment at your nearest JVC-authorized service agent.

w	+48V	+48V	u
	ON	ON
	DC INPUT
			MIC
	DC OUTPUT
e			LEN
			BREAKER
	r t	y

8 [CH-1 AUDIO IN LINE/MIC] CH-1 AUDIO select

switch

Selects the audio signal input to the 5 CH-1 AUDIO IN

connector.

LINE : Set to this position when connected to audio

equipment, etc. The reference input level is +4 dBs.

1[DV] connector

Using a DV cable (optional), a digital video component with DV connector can be connected here.

This connector is used for input and output of the DV signal or to input the VCR control signal from the digital video component with DV connector.

•To record the DV signal from this connector, set the VCR Setup Menu item No. 126 INPUT SELECT to "IEEE1394".

•To remote control the VCR with a VCR control signal from this connector, set the VCR Setup Menu item No. 050 REMOTE SELECT to "IEEE1394".

The setup level signal for the DV output connector is not provided. (NTSC only)

Bottom

4[DC INPUT] connector (XLR 4-pin)

Power input connector for 12 V DC. Connect with the AA- P250 optional AC power adapter. When a cable is connected here, the power supply from the battery pack is interrupted and the source is switched to the power supplied through this connector.

No. Signal

1GND

1	4	2	—
2	3	3	—

4+12V

MIC : Set to this position when the microphone is

connected. The reference input level is -60 dBs.

MIC +48V ON:

Set to this position when the microphone requiring

+48 V power supply (phantom microphone, etc.) is

connected.

This connector supplies +48 V DC current.

9 [CH-2 AUDIO IN LINE/MIC] CH-2 AUDIO select

switch

Selects the audio signal input to the CH-2 AUDIO IN

connector 6.

LINE : Set to this position when connected to audio

equipment, etc. The reference input level is +4 dBs.

2[EAR.] earphone jack

This is a stereo mini-jack for connecting an audio monitoring earphone. Plug in an earphone or headphone with a 3.5

mm diameter plug. (Monaural mini jack)

The earphone can also be used to monitor alarm tones depending on situations.

The sound from the monitoring loudspeaker is interrupted when an earphone is connected here.

Memo:

Only the left-channel sound is heard when a stereo mini- jack is used.

3[DC OUTPUT] connector

Power output connector to a wireless microphone transmitter, etc. The supply voltage is identical to the voltage supplied to the unit (DC 12V max. 0.1 A).

5[CH-1 AUDIO IN] CH-1 audio input connector (XLR 3-pin)

Connect the external audio equipment or microphone to this connector. Set the CH-1 AUDIO IN LINE/MIC select switch 8 according to the connected equipment.

The audio signal input through this connector is recorded on the CH-1 audio channel. To record the audio of this connector, set the CH-1 AUDIO INPUT switch 7 on page 14 to "REAR".

(AUDIO IN connector)

No. Signal

1GND

2		1	2	HOT
	3		3	COLD

MIC : Set to this position when the microphone is

connected. The reference input level is -60 dBs.

MIC +48V ON:

Set to this position when a microphone requiring +48

V power supply (phantom microphone, etc.) is

connected. This connector supplies +48 V DC

current.

CAUTION:

When connecting a component that does not require +48 V power supply, make sure that the switch is not set to this position before the connection is made.

0Battery holder

Mount a Flat Shape type battery pack here.

☞See "Attaching a Flat Shape Type Battery Pack" on page 36.

41

32

(Surface profile)

20

No. Signal

1GND

2—

3—

4DC +12V (power through)

21

For servicing

See the service manual page 1-1 “RESETTING THE POWER CIRCUIT ←

PROTECTION BREAKER”.