10. S.S.F. (Super Scene Finder) FUNCTION
10. S.S.F. (Super Scene Finder) FUNCTION
10-2 How to Use the S.S.F. Function
VF |
|
|
OFF ZEBRA |
|
|
ON | AUTO | TAKE button |
WHITE | ||
| FOCUS | |
| ACCU |
|
VTR | TAKE |
|
VTR trigger button
10-3 Deleting S.S.F. Data
FILTER
|
| ALARM |
|
| MONITOR |
| GAIN OUTPUT | WHT.BAL |
VTR |
|
NG POWER
NG button
The S.S.F. data recorded in the unit's memory can be deleted in the record mode and the
This function is only valid in the MARK mode.
In the record mode, press the NG button after the IN point has been stored or after the scene has been stored.
•The S.S.F. data of the cut that you are currently shooting is deleted.
When the NG button is pressed after the IN point has been stored, the scene number is not updated.
*The S.S.F. data of previous cuts are not deleted.
In the
At the point when the TAKE button is used to store the next scene, the S.S.F. data of the immediately preceding cut is deleted.
Note:
CUE Mode
1. Set the S.S.F. mode as CUE mode.
Set the VCR Setup Menu item No. 398 S.S.F. MODE to "CUE".
☞See page 69.
•The CUE mode is indicated in the lower part of the Status 1 screen in the viewfinder.
MARK Mode
1. Set the S.S.F. mode as MARK mode.
Set the VCR Setup Menu item No. 398 S.S.F. MODE to "MARK".
☞See page 69.
•The MARK mode is indicated in the lower part of the Status 1 screen in the viewfinder.
The NG button is only valid for the immediately preceding scene. The erase of scene data by the NG button cannot be confirmed on the unit.
10-4 Resetting S.S.F. Data
ACCU - FOCUS
|
|
|
| G | |
|
|
|
| F | |
|
|
|
| I | |
|
|
|
| SD | |
|
|
|
| B | |
| - |
|
|
| |
|
|
|
| ||
F 5 . 6 | - - - - | C 09 9 | |||
STBY |
| < 6 0 | 1 2 . 4V | ||
CUE mode Number of memorized scenes
ACCU - FOCUS
|
|
|
| G | |
|
|
|
| F | |
|
|
|
| I | |
|
|
|
| SD | |
|
|
|
| B | |
| - |
|
|
| |
|
|
|
| ||
F 5 . 6 | - - - - | M 09 9 | |||
STBY |
| < 6 0 | 1 2 . 4V | ||
MARK mode Number of memorized scenes
LOG 
REW STOP 
FF 
PLAY 
STILL
2. LOG button 1. STOP button
Operation
1. Press the STOP button to enter the stop mode.
2. Press the RESET button while the LOG button is kept pressed.
• All the S.S.F. data held in the memory are erased. |
*This indicator is not indicat- ing the number of the CUE point.
2. Press the VTR trigger button to start the recording.
However, the reel number is not cleared. |
Note:
2. Press the VTR trigger button to start the recording.
3. When you reach the point that you want to memorize as the CUE point, press the TAKE button.
•The time code data of the point where the TAKE button is pressed is stored in the unit's memory as CUE data.
The LOG button’s LED lights during memorization of the CUE point and the “∗” mark is shown in the viewfinder.
Press the TAKE button each time you reach a point that you want to memorize as CUE data.
4.Stop the recording.
Press the VTR trigger button.
Note:
3. When you reach the scene that you want to memorize, press the TAKE button.
•The time code data of the point where the TAKE button is pressed is stored in the unit's memory as the start point of the scene.
4.When you reach the scene that you want to memorize as the ending point, press the TAKE button again.
•The time code data of the point where the TAKE button is pressed is stored in the unit's memory as the ending point of the scene.
•The LOG button’s LED lights during memorization of the IN point and the “∗” mark is shown in the viewfinder.
The LOG button’s LED remains off during memorization of the OUT point and the “∗” mark is not shown in the
viewfinder.
For each scene that you want to memorize, repeat steps 3. and 4.
5.Stop the recording.
Press the VTR trigger button.
FILTER |
|
|
|
| ALARM |
|
| MONITOR |
|
| AUDIO |
|
| LEVEL |
| GAIN OUTPUT | WHT.BAL |
VTR |
|
NG POWER
2. RESET button
The unit is not provided with a function for reading out the S.S.F. data from a tape.
Necessary data should be moved to another device before resetting. Also, to read out the S.S.F. data from a tape, please use the optional DV Videocassette Recorder
•Once the S.S.F. data has been written to a videocassette, it is not possible to record S.S.F. data to the tape again.
•Once a tape with recorded S.S.F. data is rewound but not ejected before playback or recording is performed on it again, the previous S.S.F. data cannot be automatically erased when S.S.F. data are recorded (when you overwrite the previous image). Therefore, the S.S.F. data of the overlapped sections will not correspond to the video image.
Furthermore, please note that the time code data may differ from the actual data if recording is started in the CUE mode in this situation.
61
62
