For servicing
→ See the service manual page
3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS
3-6 Attaching the Tripod Base (provided)
3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS
3-7 Inserting and Replacing Backup Lithium Batteries
1.Tripod mounting holes
Front mount clip
2. Safety lever
2.
Lock lever
4.
Front base mount
3.
Rear base mount
Use the provided tripod base to place the camera on a tripod.
1. Attach the tripod base on the tripod by using the hole that balances the unit most optimally.
2. While pushing the safety lever, pull the lock lever toward the front until the front mount clip clicks into place.
3. Place the unit on the tripod base by aligning the rear base mount of the unit with the pin on the tripod base.
4. Push the unit from the upward direction and slide it toward the front so that the front base mount of the unit is locked by the front mount clip of the tripod base as it clicks into place.
CAUTION:
•The front base mount may be locked while the pin of the tripod base is not inserted into the hole on the rear base mount of the unit. Therefore, after mounting, make sure that these parts are engaged properly.
•When moving the unit mounted on a tripod, any impact or vibration should be avoided as this may cause the unit to become detached and to drop from the tripod.
Be sure to remove the unit from the tripod before transporting it.
The
●Lithium battery: CR2032
|
|
|
| "Li" indicator |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| CAUTION: |
|
| |
|
|
|
|
|
|
|
|
|
| If the unit is not used for a lengthy period of time (one | |||
|
|
|
|
|
|
|
|
|
| month or more), remove the lithium battery. If the voltage | |||
|
|
|
|
|
|
|
|
|
| of the lithium battery becomes low, the set may malfunction. | |||
|
| OPERATE/WARNING |
|
|
|
|
|
|
|
|
|
| |
| RESET | CH 1 |
|
| AUTO OFF DEW | LIGHT |
|
|
|
|
| ||
|
| CH 2 |
|
| SERVO RF L i | OFF |
|
|
|
|
| ||
|
| 32k | 48k | PB |
| NDF | HOLD |
|
|
|
|
|
|
| MONITOR AUD LOCK SP |
|
|
|
| COUNTER |
|
|
|
|
| ||
FILTER | SELECT |
|
| REV | FWD | E | BATT F | AUDIO |
|
| |||
1 3200k | ALARM |
| REMAIN | TC |
|
| |||||||
|
|
|
|
| CTL |
|
|
|
| TC GENERATOR | |||
2 5600k |
|
|
|
|
|
|
| UB |
| LEVEL | |||
3 5600k+ND |
|
|
|
|
|
|
|
|
|
| |||
SHUTTER STATUS |
|
|
|
|
|
|
|
|
|
| AUTO | PRESET | FREE |
MONITOR |
|
|
|
|
|
|
|
|
| MANUAL | REGEN | REC | |
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| AUDIO SELECT |
| |
MENU
| AUDIO INPUT |
|
|
| |
| CONTINUE | MENU | |||
LEVEL |
| FRONT |
|
|
|
|
|
|
|
| |
|
| REAR |
|
|
|
LITHIUM BATT. |
| GROUP | ITEM | SELECT | DATA SET |
|
| HOLD | SHIFT | ADVANCE | PRESET |
VTR | GAIN | OUTPUT WHT.BAL |
|
NG | POWER |
ON | OFF |
Lithium battery case
Power switch
When the lithium battery is not in place or the battery is exhausted and requires a replacement, the "Li" indicator in the LCD display will light up.
Replace lithium batteries with the POWER switch set to ON. Doing it with the POWER switch set to OFF will cause the loss of backup data.
Front mount clip
Pin
4.
POWER
How to Install the Lithium Battery
Lithium battery cover
CR2032
LITHIUM BATT.
CR2032
1. Push the lithium battery cover in the direction of the arrow as illustrated and remove the cover.
2. Slide the battery into place with its 
marked surface facing upward.
3. Return the lithium battery cover to its original position in the unit.
How to Remove Lithium Batteries
| The lithium battery is easily removed | |
CR2032 | if you press at the edge of the | |
lithium battery at the place | ||
|
indicated in the illustration on the left and then pull the battery out.
After replacing the lithium battery, set the date and time. To do this, see page 41 “Setting the Date and Time”.
3334
