JVC GY-DV500 Indications in Viewfinder Contd,  Warning LED Indicators Inside the Viewfinder

2. CONTROLS, INDICATORS AND CONNECTORS

2-9 Indications in Viewfinder

2. CONTROLS, INDICATORS AND CONNECTORS

2-9 Indications in Viewfinder (Cont'd)

WARNING LED INDICATORS INSIDE THE VIEWFINDER

ACCU - FOCUS

G

F

1
	ACCU - FOCUS
2	G
3	F

1

2

3

SCENE	F I L E	A
WH I TE	BA L	A
F I L TER		3	. 2 K
SHUT TER		1	/ 1 0 0 0
GA I N		6 d B

BATT	REC
	ALARM

The viewfinder has two LED indicators below the screen. These LEDs light or blink to indicate the present status of the camera or the VCR.

● [BATT] battery lamp

This lights red when the battery voltage becomes too low for

operating the camera.

● REC/ALARM lamp

I

SD

B

7

4

57 SDI

6			B
	CH1	- - - - + - -
F 5 . 6	CH2	- - - - + - -	M 09 9
STBY		< 6 0	1 2 . 4V

9 B 0 8 A

4

5

6 C

I R I S	L EVE L	NORMA L
I R I S DETECT		NORMA L
FUL L	AUTO	OF F
REC	T I ME	< 6 0

BATTREC/ALARM

LampLamp

This lights or blinks green under the following circumstances.

Steady green : During recording.

Blinks green : • While the GY-DV500 switches from record- pause to recording.

•Immediately before the tape is running out or when it has run out.

•When an error occurs in the GY-DV500.

	Status 0		Status 1	Status 2
● Status 0
	Display Position	Display	Function
1		ACCU-FOCUS	Blinks during the ACCU-FOCUS operation.

VIEWFINDER SCREEN DISPLAY

The following indications are displayed on the viewfinder screen. (However, this information is not displayed while the VCR section is playing back a tape.)

Status screens (screens for use in checking the current camera settings)

Alarm message display

Safety zone display

Setting screen (screen for use in the camera and VCR setup)

Auto white balance display

Shutter speed display

	SKIN AREA	Blinks while the skin tone detail color area is displayed.
	S	Displayed when the SHUTTER or V-SCAN is ON.
	FAS	Displayed when the Full Auto Shooting is ON.
	ALC	Displayed when the ALC alone is ON.
2	G	Displayed in other modes than 0 dB, LOLUX and ALC.
	L	Displayed during LOLUX operation.
3	F	Displayed when FAW alone is ON.
4	I	Displayed when IRIS BACK LIGHT or IRIS SPOT LIGHT is selected.
5	SD	Displayed while the Skin Detail function is in operation.
6	B	Displayed when BLACK STRETCH or BLACK COMPRESSION is selected.

Status Screens

STATUS button

FILTER

1	3200k			ALARM
2	5600k
3	5600k+ND
SHUTTER		STATUS		MONITOR
MENU
		FULL AUTO BLACK
			OUTPUT	L
VTR		GAIN		WHT.BA
		NG	POWER
			ON	OFF

Press the STATUS button during normal screen display to show one of the status screens in the viewfinder. One of the three status screens will be displayed every time the button is pressed.

	OPERATE/WARNING
	LIGHT
RESET	ON
	OFF
MONITOR	COUNTER
SELECT
	CTL
	TC
	UB

CH-1 AUDIO CH-2

LEVEL

7 Event display See the table below.

7Event display

Event is displayed in the viewfinder for only about 2 seconds when any of the following switches is operated.

Switch		Event Display Contents
ZEBRA	ZEBRA	ON, OFF
BLACK	BLACK	STRETCH, NORMAL, COMPRESS
GAIN	GAIN	–3 dB, 0 dB, 6 dB, 9 dB, 12 dB, 18 dB, ALC
WHT. BAL	WHITE BAL	A, B, PRESET, FAW
FULL AUTO	FULL AUTO	ON, OFF
AUTO IRIS	IRIS	BACK.L, NORMAL, SPOT.L
LOLUX	LOLUX	ON, OFF
FILTER knob	FILTER	3.2K, 5.6K, 5.6K+ND
VTR	VTR	STBY, SAVE
AUTO KNEE	AUTO KNEE	ON, OFF

ACCU - FOCUS

G

F

I

SD

B

ACCU - FOCUS

			G
			F
			I
			SD
			B
	CH1 -	- - - + - -
F 5 . 6	CH2 -	- - - + - -	M 09 9
STBY		< 6 0	1 2 . 4V

SCENE	F I L E	A
WH I TE	BA L	A
F I L TER		3 .	2 K
SHUT TER		1 /	1 0 0 0
GA I N		6 d B
I R I S	L EVE L	NORMA L
I R I S DETECT		NORMA L
FUL L	AUTO	OF F
REC T I ME		< 6	0

Status 0 Status 1 Status 2

25

26 27