Manuals / MRV Communications / Computer Equipment / Network Card

MRV Communications TS700/G, TS700/155, TS800/155, TS700/100 Display and Results, Indicators

Models: TS800/155 TS700/100 TS700/155 TS700/G

1 77

Download 77 pages 1.79 Kb

Page 39

Loop-back Airlink BER test

M R V C o m m u n i c a t i o n s , I n c . – I n s t a l l a t i o n M a n u a l

Configuration 3: (Applicable to all models)

BER Tester

RX TX

	IR link
TX	TX
TS	TS
UWIN	UWIN
RX	RX

Configuration 4: (Applicable to all models)

Whole configuration operating test (Ping test or File transfer) for Ethernet or Fast Ethernet systems

Peripheral

Equipment

TX RX

Workstation

TX

RX

UWINTS

IR link

TSUWIN

Peripheral

Equipment

	RX	TX

Workstation

TX

RX

Configuration 5: (Applicable to all models)

Whole configuration operating test for all models

Peripheral/

Testing

Equipment

STP cable

Or F/O Cable

TereScope

					Peripheral/
						Testing
						Equipment

	IR link							STP
	IR link							cable
								cable
				TereScope				Or F/O Cable

Display and Results

1.TS700/155,TS800/155&TS800/155-F

Proper Display

1.Indicators

Indicator →	AIR RX		F/O RX			Alignment	Loopback
Position ↓	Flag	Sync	Flag	Sync
ON	x	x	x	x
OFF						x	x
			Table 7:	Indicators

29

Image 39

MRV Communications TS700/G, TS700/155, TS800/155, TS700/100 user manual Display and Results, Indicators

Contents

UserManual UserManual TableofContents P E N D I CE Mark StandardsStandards Compliance FCC Notice Trademarks MRV  Laser Safety CertificationOther Standards Disclaimer AboutthisUserManual Before Installing SafetyRequirements Servicing Introduction Carefully Read the Entire Manual Before Installing Using the Part Number for Ordering TheProductModels Part Number Description Front MRV Back Panel Description TS800/155 Standard Model DS1 Toggles Data Rate DIP switch TS800/155-F Standard Model including Fusion option RF Transceiver Fusion Operation Mode 5b TS & Fusion Fusion TS700/100 Fast-Ethernet System OFF Auto-negotiation, on Forced MRV Display LEDs,Dry Monitoring and Management options ManagementDry contact Only TS800 Typical Connection Fiber ConnectionCopper Connection Location & Range SiteSurveyLine of Sight Orientation Consult Factory in Case of Doubt Optimal Mounting Unacceptable Mounting Mounting Environment & StabilityPage Transmitting through a Window Wall Mounting using JMP and JMB 12 shows the arrangement for transmitting through a window Power Data/Signal CablingInfrastructure Handle the Fibers Very Carefully Test equipment SetupBenchTest Compatibility TS700/100Fastethernet IR link Bench test Display and Results Indicators Expected Results Received power Installation AccessoriesDescription TereScope Parts External view Part Description Aiming Head Adjustment and Locks Installer Tool Kit JITK-L MountingDetachment of the TS from the JMP-L Standard position a Mounting the accessories Mounting on the floor Special Mounting JMP-L Mounting on a fragile/crumbly wall 17 Alignment kit mountedon JMP-L Back view Attachment of the Transceiver TereScope Head Powering on the TereScope AimingProcedure Tools and Equipment ProcedureTransceiver Alignment General Fine Alignment 13 Position after the horizontal aiming 15a and 6.15b Alignment screws Visual Inspection InstallationCompletionLink Operating Test Before Closing the Rear Door 17 Mounted TereScope Left View Maintenance Accuracy should be examined and restored if necessaryPeriodic Visits Appendix a TS700/100 Fast-Ethernet Light TS800/155 high speed Light TS700/G Giga-Light Appendixb Packing box contains Appendixc Appendixd List of the Tools Supplied by MRV Communications Where to use Points to Remember Introduction Interference Figure E.3 Active Transmitters Shown Darkened Page Appendixf Effect of Wind on Terescopes FSO Chaining AppendixG Indirect Chaining Use the indoor switch in building C for the chaining FSO products & Chaining Product series No of chained links Appendixh Site survey Installation System failure Appendixi